The design report

More documents

Recommendations

Info

Executive Summary 1 Design Requirements and Objectives 2 Conceptual Design 3 Synthesis of concept 3.1 Configuration design 3.1.1 Initial Sizing 3.1.2 Fuselage layout 3.1.3 Airfoil design 3.1.4 Wing planform design 3.1.5 Empennage design 3.1.6 Geometry for landing gear 3.1.7 Control surface sizing 3.1.8 Pod Layout 3.1.9 Analysis of concept 3.2 Analysis of propulsion system 3.2.1 Weight estimation and Centre of Gravity (cg) estimation 3.2.2 Stability and Aerodynamic performance analysis 3.2.3 Aircraft performance analysis 3.2.4 CAD definition of the concept 3.2.5
Preliminary and Detailed Design 4 Structure layout, initial sizing, and internal layout Design 4.1 Wing structure 4.1.1 Fuselage structure 4.1.2 Empennage structure 4.1.3 Control surface structure 4.1.4 Landing gear 4.1.5 Integration of propulsion and control system 4.1.6 Pod Structure 4.1.7 Payload arrangement 4.1.8 Structural analysis 4.2 Fabrication 5 Preparation for materials 5.1 Fuselage fabrication 5.2 Wing fabrication (inner section) 5.3 Wing fabrication (outer section) 5.4 Empennage fabrication (inner section) 5.5 Landing gear fabrication 5.6 Installation propulsion system in to airframe and test 5.7 Control system installation and test 5.8 Control surface fabrication 5.9 Assembly and test 5.10 Measurement of Weight and CG location 5.11
Page 1: EP-UAV Project 2009 iSpy Kate Rietd
Page 5 and 6: Executive Summary 1 iSpy is a twin
Page 7 and 8: Design Requirements and Objectives
Page 9 and 10: Initial Sizing 3.1.2 Estimating air
Page 11 and 12: Airfoil design 3.1.4 Wing: Before t
Page 13 and 14: Tail: A symmetric airfoil with a th
Page 15: Empennage design 3.1.6 The dimensio
Page 19 and 20: Pod Layout 3.1.9 The pod of the air
Page 21: Weight estimation and Centre of Gra
Page 26 and 27: Figure 3.2.303 - Stability axis der
Page 30 and 31: CAD definition of the concept 3.2.5
Page 32 and 33: Figure 3.2.505: The vertical tail F
Page 34 and 35: Preliminary and Detailed Design 4 S
Page 36 and 37: Figure 4.1.109 Figure 4.1.110 The c
Page 38 and 39: Material type was chosen for each c
Page 40 and 41: The nose section of the fuselage co
Page 42 and 43: This part of the fuselage is the mo
Page 44 and 45: Empennage structure 4.1.3 Prelimina
Page 46 and 47: An ‘L’ shaped support was also
Page 48 and 49: Landing gear 4.1.5 Initial stages o
Page 50 and 51: Pod Structure 4.1.7 Figure 4.1.701-
Page 52 and 53:
Fuselage fabrication 5.2 Since ther
Page 54 and 55:
The servo holder plates in front of
Page 56 and 57:
Landing gear fabrication 5.5 The de
Page 58 and 59:
Fabrication of Pod 5.6 Like the fus
Page 60 and 61:
Control surface fabrication 5.9 Ail
Page 62 and 63:
Note: The weights taken after fabri
Page 64 and 65:
It was here that the first problem
Page 66 and 67:
Flight Test 6.2 The flight test aim
Page 68 and 69:
Appendix 7 Appendix A - AVL files i
Page 70 and 71:
TRANSLATE -0.450 0.384 0.00 # BFIL
Page 72 and 73:
CLARK YM-15 - Re = 250000 Alfa Cl C
Page 74 and 75:
Appendix C - Preparation of materia
Page 76 and 77:
Appendix D - Control surface sizing
Page 82 and 83:
Conceptual Design Preliminary Desig
show all

The design report

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?