Library manual M238 system functions | 2 MB - BERGER - POSITEC

More documents

Recommendations

Info

<strong>M238</strong> System Variables PLC_R: Controller Read Only System Variables Variable Structure The following table describes the parameters of the PLC_R System Variable (PLC_R_STRUCT type): %MW Var Name Type Comment 60000 i_wVendorID WORD Controller Vendor ID. 101A hex = Schneider Electric 60001 i_wProductID WORD Controller Reference ID. NOTE: Vendor ID and Reference ID are the components of the Target ID of the Controller displayed in the Communication Settings view (Target ID = 101A XXXX hex). 60002 i_dwSerialNumber DWORD Controller Serial Number 60004 i_byFirmVersion[0..3] ARRAY[0..3] OF BYTE Controller Firmware Version [aa.bb.cc.dd]: i_byFirmVersion[0] = aa ... i_byFirmVersion[3] = dd 60006 i_byBootVersion[0..3] ARRAY[0..3] OF BYTE Controller Boot Version [aa.bb.cc.dd]: i_byBootVersion[0] = aa ... i_byBootVersion[3] = dd 60008 i_dwHardVersion DWORD Controller Hardware Version. 60010 i_dwChipVersion DWORD Controller Coprocessor Version. 60012 i_wStatus PLC_R_STATUS (see page 53) State of the controller. 60013 i_wBootProjectStatus PLC_R_BOOT_PROJECT_STATUS (see page 55) 60014 i_wLastStopCause PLC_R_STOP_CAUSE (see page 57) 60015 i_wLastApplicationError PLC_R_APPLICATION_ERROR (see page 54) Returns information about the boot application stored in FLASH memory. Cause of the last transition from RUN to another state. Cause of the last Controller Exception. 60016 i_lwSystemFault_1 LWORD Bit field FFFF FFFF FFFF FFFF hex indicates no detected error. If TM2 error is detected, the bit 1 is FALSE. 60020 i_lwSystemFault_2 LWORD Not used. 16 EIO0000000364 04/2012
%MW Var Name Type Comment 60024 i_wIOStatus1 PLC_R_IO_STATUS (see page 56) 60025 i_wIOStatus2 PLC_R_IO_STATUS (see page 56) Embedded I/O status. TM2 I/O status. <strong>M238</strong> System Variables 60026 i_wBatteryStatus WORD Charge remaining in the battery. This System Variable can take the following significant values: FFFF hex = 100% = 3.5 V 7FFF hex = 50% = 2.75 V 0000 hex = 0% = 2 V Flashing thresholds of the Batt LED: 100% = always OFF 50% = periodic flashing 0% = always ON 60028 i_dwAppliSignature1 DWORD 1st DWORD of 4 DWORD signature (16 bytes total). The Application Signature is generated by the software during build. 60030 i_dwAppliSignature2 DWORD 2nd DWORD of 4 DWORD signature (16 bytes total). The Application Signature is generated by the software during build. 60032 i_dwAppliSignature3 DWORD 3rd DWORD of 4 DWORD signature (16 bytes total). The Application Signature is generated by the software during build. 60034 i_dwAppliSignature4 DWORD 4th DWORD of 4 DWORD signature (16 bytes total). The Application Signature is generated by the software during build. EIO0000000364 04/2012 17
Page 1 and 2: EIO0000000364.06 Modicon M238 Logic
Page 3 and 4: Table of Contents Safety Informatio
Page 5 and 6: Important Information NOTICE Safety
Page 7 and 8: At a Glance Document Scope Validity
Page 9 and 10: Overview Modicon M238 Logic Control
Page 11 and 12: Understanding System Variables Intr
Page 13 and 14: Using System Variables Introduction
Page 15: 1.2 PLC_R and PLC_W Structures Over
Page 19 and 20: 1.3 SERIAL_R and SERIAL_W Structure
Page 21 and 22: SERIAL_W[0..1]: Serial Line Read /
Page 25 and 26: GetBatteryLevel: Returns Remaining
Page 27 and 28: GetEventsNumber: Returns the Number
Page 29 and 30: Example M238 System Functions This
Page 31 and 32: GetLastStopCause: Returns the Cause
Page 33 and 34: GetLocalIOStatus: Returns the Embed
Page 35 and 36: GetPlcFault: Returns Detected Error
Page 37 and 38: M238 System Functions I/O Expansion
Page 39 and 40: Example M238 System Functions To ob
Page 41 and 42: M238 System Functions GetShortCutSt
Page 43 and 44: IsFirstMastCycle: Indicates if Cycl
Page 45 and 46: M238 System Functions IsFirstMastWa
Page 47 and 48: InhibitBatLowLed: Disables or Re-en
Page 49 and 50: SetRTCDrift: Adjust the Real Time C
Page 53 and 54: PLC_R_STATUS: Controller Status Cod
Page 55 and 56: PLC_R_BOOT_PROJECT_STATUS: Boot Pro
Page 57 and 58: M238 PLC System Library Data Types
Page 59 and 60: 3.2 System Functions Data Types Ove
Page 67 and 68:
HOUR: SetRTCDrift Function Hour Par
Page 69 and 70:
Modicon M238 Logic Controller EIO00
Page 71 and 72:
Overview Modicon M238 Logic Control
Page 73 and 74:
How to Use a Function or a Function
Page 75 and 76:
Function and Function Block Represe
Page 77 and 78:
How to Use a Function or a Function
Page 79 and 80:
Function and Function Block Represe
Page 81 and 82:
1-phase counter 2-phase counter BOO
Page 83 and 84:
expansion bus E Glossary The expans
Page 85 and 86:
Modbus NEMA PLC PLI POU PTO M The M
Page 87 and 88:
U unlocated variable An unlocated v
Page 89 and 90:
Modicon M238 Logic Controller Index
Page 91 and 92:
System Variable PLC_R, 16 PLC_W, 18
show all

Library manual M238 system functions | 2 MB - BERGER - POSITEC

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?