Library manual M238 system functions | 2 MB - BERGER - POSITEC

More documents

Recommendations

Info

M238 System Functions GetSerialNumber: Returns the Serial Number of the Controller Function Description This function returns the serial number of the Controller. NOTE: The similar information is also available through the System Variable (bit0 and bit1) PLC_R.i_dwSerialNumber (see page 16). Graphical Representation IL and ST Representation To see the general representation in IL or ST language, refer to the chapter Function and Function Block Representation (see page 71). I/O Variable Description The following table describes the output variable: Output Type Comment GetSerialNumber DWORD Controller Serial number. 40 EIO0000000364 04/2012
M238 System Functions GetShortCutStatus: Returns the Short-Circuit Status on Embedded Outputs Function Description This function returns the short-circuit or overload diagnostic on embedded outputs. NOTE: For more information about embedded outputs management, refer to the M238 Hardware Guide (see M238 Logic Controller, Hardware Guide). Graphical Representation IL and ST Representation To see the general representation in IL or ST language, refer to the chapter Function and Function Block Representation (see page 71). I/O Variable Description The following table describes the output variable: Parameter Type Comment GetShortCutStatus WORD see bit field description below The following table describes the bit field for the TM238LDD24DT and TM238LFDC24DT : Bit Description 0 TRUE = short-circuit on outputs group 1 (Q0 to Q3). 1 TRUE = short-circuit on outputs group 2 (Q4 to Q6). 2 TRUE = short-circuit on outputs group 3 (Q7 to Q9). The following table describes the bit field for the TM238LDA24DR and TM238LFAC24DR : Bit Description 0 TRUE = short-circuit on outputs group 1 (Q0 to Q3). EIO0000000364 04/2012 41
Page 1 and 2: EIO0000000364.06 Modicon M238 Logic
Page 3 and 4: Table of Contents Safety Informatio
Page 5 and 6: Important Information NOTICE Safety
Page 7 and 8: At a Glance Document Scope Validity
Page 9 and 10: Overview Modicon M238 Logic Control
Page 11 and 12: Understanding System Variables Intr
Page 13 and 14: Using System Variables Introduction
Page 15 and 16: 1.2 PLC_R and PLC_W Structures Over
Page 17 and 18: %MW Var Name Type Comment 60024 i_w
Page 19 and 20: 1.3 SERIAL_R and SERIAL_W Structure
Page 21 and 22: SERIAL_W[0..1]: Serial Line Read /
Page 25 and 26: GetBatteryLevel: Returns Remaining
Page 27 and 28: GetEventsNumber: Returns the Number
Page 29 and 30: Example M238 System Functions This
Page 31 and 32: GetLastStopCause: Returns the Cause
Page 33 and 34: GetLocalIOStatus: Returns the Embed
Page 35 and 36: GetPlcFault: Returns Detected Error
Page 37 and 38: M238 System Functions I/O Expansion
Page 39: Example M238 System Functions To ob
Page 43 and 44: IsFirstMastCycle: Indicates if Cycl
Page 45 and 46: M238 System Functions IsFirstMastWa
Page 47 and 48: InhibitBatLowLed: Disables or Re-en
Page 49 and 50: SetRTCDrift: Adjust the Real Time C
Page 53 and 54: PLC_R_STATUS: Controller Status Cod
Page 55 and 56: PLC_R_BOOT_PROJECT_STATUS: Boot Pro
Page 57 and 58: M238 PLC System Library Data Types
Page 59 and 60: 3.2 System Functions Data Types Ove
Page 67 and 68: HOUR: SetRTCDrift Function Hour Par
Page 69 and 70: Modicon M238 Logic Controller EIO00
Page 73 and 74: How to Use a Function or a Function
Page 75 and 76: Function and Function Block Represe
Page 77 and 78: How to Use a Function or a Function
Page 79 and 80: Function and Function Block Represe
Page 81 and 82: 1-phase counter 2-phase counter BOO
Page 83 and 84: expansion bus E Glossary The expans
Page 85 and 86: Modbus NEMA PLC PLI POU PTO M The M
Page 87 and 88: U unlocated variable An unlocated v
Page 89 and 90: Modicon M238 Logic Controller Index
Page 91 and 92:
System Variable PLC_R, 16 PLC_W, 18
show all

Library manual M238 system functions | 2 MB - BERGER - POSITEC

Create successful ePaper yourself

Delete template?

Save as template?