Library manual M238 system functions | 2 MB - BERGER - POSITEC

More documents

Recommendations

Info

M238 System Variables PLC_W: Controller Read / Write System Variables Variable Structure The following table describes the parameters of the PLC_W System Variable (PLC_W_STRUCT type): %MW Var Name Type Comment n/a q_uiOpenPLCControl UINT When Value pass from 0 to 6699, The command previously written in the following PLC_W.q_wPLCControl is executed. n/a q_wPLCControl PLC_W_COMMAND (see page 58) Controller RUN / STOP command executed when the system variable PLC_R.q_uiOpenPLCControl value pass from 0 to 6699. NOTE: n/a means that there is no predefined %MW mapping for this System Variable. 18 EIO0000000364 04/2012
1.3 SERIAL_R and SERIAL_W Structures Overview M238 System Variables This section lists and describes the different System Variables included in the SERIAL_R and SERIAL_W structures. What’s in this Section? This section contains the following topics: Topic Page SERIAL_R[0..1]: Serial Line Read Only System Variables 20 SERIAL_W[0..1]: Serial Line Read / Write System Variables 21 EIO0000000364 04/2012 19
Page 1 and 2: EIO0000000364.06 Modicon M238 Logic
Page 3 and 4: Table of Contents Safety Informatio
Page 5 and 6: Important Information NOTICE Safety
Page 7 and 8: At a Glance Document Scope Validity
Page 9 and 10: Overview Modicon M238 Logic Control
Page 11 and 12: Understanding System Variables Intr
Page 13 and 14: Using System Variables Introduction
Page 15 and 16: 1.2 PLC_R and PLC_W Structures Over
Page 17: %MW Var Name Type Comment 60024 i_w
Page 21 and 22: SERIAL_W[0..1]: Serial Line Read /
Page 25 and 26: GetBatteryLevel: Returns Remaining
Page 27 and 28: GetEventsNumber: Returns the Number
Page 29 and 30: Example M238 System Functions This
Page 31 and 32: GetLastStopCause: Returns the Cause
Page 33 and 34: GetLocalIOStatus: Returns the Embed
Page 35 and 36: GetPlcFault: Returns Detected Error
Page 37 and 38: M238 System Functions I/O Expansion
Page 39 and 40: Example M238 System Functions To ob
Page 41 and 42: M238 System Functions GetShortCutSt
Page 43 and 44: IsFirstMastCycle: Indicates if Cycl
Page 45 and 46: M238 System Functions IsFirstMastWa
Page 47 and 48: InhibitBatLowLed: Disables or Re-en
Page 49 and 50: SetRTCDrift: Adjust the Real Time C
Page 53 and 54: PLC_R_STATUS: Controller Status Cod
Page 55 and 56: PLC_R_BOOT_PROJECT_STATUS: Boot Pro
Page 57 and 58: M238 PLC System Library Data Types
Page 59 and 60: 3.2 System Functions Data Types Ove
Page 67 and 68: HOUR: SetRTCDrift Function Hour Par
Page 69 and 70:
Modicon M238 Logic Controller EIO00
Page 71 and 72:
Overview Modicon M238 Logic Control
Page 73 and 74:
How to Use a Function or a Function
Page 75 and 76:
Function and Function Block Represe
Page 77 and 78:
How to Use a Function or a Function
Page 79 and 80:
Function and Function Block Represe
Page 81 and 82:
1-phase counter 2-phase counter BOO
Page 83 and 84:
expansion bus E Glossary The expans
Page 85 and 86:
Modbus NEMA PLC PLI POU PTO M The M
Page 87 and 88:
U unlocated variable An unlocated v
Page 89 and 90:
Modicon M238 Logic Controller Index
Page 91 and 92:
System Variable PLC_R, 16 PLC_W, 18
show all

Library manual M238 system functions | 2 MB - BERGER - POSITEC

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?