Library manual M238 system functions | 2 MB - BERGER - POSITEC

More documents

Recommendations

Info

Glossary HMI HSC IEC 61131-3 IL LD located variable H A human-machine interface is an operator interface (usually graphical) for industrial equipment. high-speed counter I The IEC 61131-3 is an international electrotechnical commission standard for industrial automation equipment (like controllers). IEC 61131-3 deals with controller programming languages and defines 2 graphical and 2 textual programming language standards: graphical: ladder diagram, function block diagram textual: structured text, instruction list A program written in the Instruction List language is composed of a series of instructions executed sequentially by the controller. Each instruction includes a line number, an instruction code, and an operand. (IL is IEC 61131-3 compliant.) L A program in the Ladder Diagram language includes a graphical representation of instructions of a controller program with symbols for contacts, coils, and blocks in a series of rungs executed sequentially by a controller. IEC 61131-3 compliant. A located variable has an address. (See unlocated variable.) 84 EIO0000000364 04/2012
Modbus NEMA PLC PLI POU PTO M The Modbus communication protocol allows communications between many devices connected to the same network. N Glossary The National Electrical Manufacturers Association publishes standards for the performance of various classes of electrical enclosures. The NEMA standards cover corrosion resistance, ability to protect from rain and submersion, etc. For IEC member countries, the IEC 60529 standard classifies the ingress protection rating for enclosures. P The Programmable Logic Controller is the “brain” of an industrial manufacturing process. It automates a process, used instead of relay control <strong>system</strong>s. PLCs are computers suited to survive the harsh conditions of the industrial environment. Pulse Latch Input A Program Organization Unit includes a variable declaration in source code and the corresponding instruction set. POUs facilitate the modular reuse of software programs, <strong>functions</strong>, and function blocks. Once declared, POUs are available to one another. SoMachine programming requires the utilization of POUs. Pulse Train Outputs are used to control for instance stepper motors in open loop. EIO0000000364 04/2012 85
Page 1 and 2:
EIO0000000364.06 Modicon M238 Logic
Page 3 and 4:
Table of Contents Safety Informatio
Page 5 and 6:
Important Information NOTICE Safety
Page 7 and 8:
At a Glance Document Scope Validity
Page 9 and 10:
Overview Modicon M238 Logic Control
Page 11 and 12:
Understanding System Variables Intr
Page 13 and 14:
Using System Variables Introduction
Page 15 and 16:
1.2 PLC_R and PLC_W Structures Over
Page 17 and 18:
%MW Var Name Type Comment 60024 i_w
Page 19 and 20:
1.3 SERIAL_R and SERIAL_W Structure
Page 21 and 22:
SERIAL_W[0..1]: Serial Line Read /
Page 23 and 24:
Overview Modicon M238 Logic Control
Page 25 and 26:
GetBatteryLevel: Returns Remaining
Page 27 and 28:
GetEventsNumber: Returns the Number
Page 29 and 30:
Example M238 System Functions This
Page 31 and 32:
GetLastStopCause: Returns the Cause
Page 33 and 34: GetLocalIOStatus: Returns the Embed
Page 35 and 36: GetPlcFault: Returns Detected Error
Page 37 and 38: M238 System Functions I/O Expansion
Page 39 and 40: Example M238 System Functions To ob
Page 41 and 42: M238 System Functions GetShortCutSt
Page 43 and 44: IsFirstMastCycle: Indicates if Cycl
Page 45 and 46: M238 System Functions IsFirstMastWa
Page 47 and 48: InhibitBatLowLed: Disables or Re-en
Page 49 and 50: SetRTCDrift: Adjust the Real Time C
Page 51 and 52: Overview Modicon M238 Logic Control
Page 53 and 54: PLC_R_STATUS: Controller Status Cod
Page 55 and 56: PLC_R_BOOT_PROJECT_STATUS: Boot Pro
Page 57 and 58: M238 PLC System Library Data Types
Page 59 and 60: 3.2 System Functions Data Types Ove
Page 67 and 68: HOUR: SetRTCDrift Function Hour Par
Page 69 and 70: Modicon M238 Logic Controller EIO00
Page 71 and 72: Overview Modicon M238 Logic Control
Page 73 and 74: How to Use a Function or a Function
Page 75 and 76: Function and Function Block Represe
Page 77 and 78: How to Use a Function or a Function
Page 79 and 80: Function and Function Block Represe
Page 81 and 82: 1-phase counter 2-phase counter BOO
Page 83: expansion bus E Glossary The expans
Page 87 and 88: U unlocated variable An unlocated v
Page 89 and 90: Modicon M238 Logic Controller Index
Page 91 and 92: System Variable PLC_R, 16 PLC_W, 18
show all

Library manual M238 system functions | 2 MB - BERGER - POSITEC

Create successful ePaper yourself

Delete template?

Save as template?