Library manual M238 system functions | 2 MB - BERGER - POSITEC

More documents

Recommendations

Info

<strong>M238</strong> System Functions GetLastStopTime: Returns the Date and Time of the Last Detected Stop Function Description This function returns the date and time of the last transition from RUN to another state. Graphical Representation IL and ST Representation To see the general representation in IL or ST language, refer to the chapter Function and Function Block Representation (see page 71). I/O Variable Description The following table describes the output variable: Output Type Comment GetLastStopTime DWORD The time of the last detected STOP in seconds beginning with January 1, 1970 at 00:00. 32 EIO0000000364 04/2012
GetLocalIOStatus: Returns the Embedded I/O Status <strong>M238</strong> System Functions Function Description This function returns the embedded I/O status. NOTE: The similar information is also available through the System Variable PLC_R.i_wLocalIOStatus (see page 16). Graphical Representation IL and ST Representation To see the general representation in IL or ST language, refer to the chapter Function and Function Block Representation (see page 71). I/O Variables Description The following table describes the input parameter: Example 1 Input Type Comment Mode LOCAL_IO_GET_STATUS (see page 63) The following table describes the output variable: Parameter of the function: currently only LOCAL_IO_GET_GEN_STATUS (00 hex) (see page 63) is available. Output Type Comment GetLocalIOStatus LOCAL_IO_GEN_STATUS (see page 64) Status of the embedded I/O. This example shows a direct use of LOCAL_IO_GET_GEN_STATUS enumerator of the LOCAL_IO_GET_STATUS enumeration type for the Mode input parameter: VAR MyLocalIOStatus : LOCAL_IO_GEN_STATUS; END_VAR MyLocalIOStatus := GetLocalIOStatus(LOCAL_IO_GET_GEN_STATUS); EIO0000000364 04/2012 33
Page 1 and 2: EIO0000000364.06 Modicon M238 Logic
Page 3 and 4: Table of Contents Safety Informatio
Page 5 and 6: Important Information NOTICE Safety
Page 7 and 8: At a Glance Document Scope Validity
Page 9 and 10: Overview Modicon M238 Logic Control
Page 11 and 12: Understanding System Variables Intr
Page 13 and 14: Using System Variables Introduction
Page 15 and 16: 1.2 PLC_R and PLC_W Structures Over
Page 17 and 18: %MW Var Name Type Comment 60024 i_w
Page 19 and 20: 1.3 SERIAL_R and SERIAL_W Structure
Page 21 and 22: SERIAL_W[0..1]: Serial Line Read /
Page 25 and 26: GetBatteryLevel: Returns Remaining
Page 27 and 28: GetEventsNumber: Returns the Number
Page 29 and 30: Example M238 System Functions This
Page 31: GetLastStopCause: Returns the Cause
Page 35 and 36: GetPlcFault: Returns Detected Error
Page 37 and 38: M238 System Functions I/O Expansion
Page 39 and 40: Example M238 System Functions To ob
Page 41 and 42: M238 System Functions GetShortCutSt
Page 43 and 44: IsFirstMastCycle: Indicates if Cycl
Page 45 and 46: M238 System Functions IsFirstMastWa
Page 47 and 48: InhibitBatLowLed: Disables or Re-en
Page 49 and 50: SetRTCDrift: Adjust the Real Time C
Page 53 and 54: PLC_R_STATUS: Controller Status Cod
Page 55 and 56: PLC_R_BOOT_PROJECT_STATUS: Boot Pro
Page 57 and 58: M238 PLC System Library Data Types
Page 59 and 60: 3.2 System Functions Data Types Ove
Page 67 and 68: HOUR: SetRTCDrift Function Hour Par
Page 69 and 70: Modicon M238 Logic Controller EIO00
Page 73 and 74: How to Use a Function or a Function
Page 75 and 76: Function and Function Block Represe
Page 77 and 78: How to Use a Function or a Function
Page 79 and 80: Function and Function Block Represe
Page 81 and 82: 1-phase counter 2-phase counter BOO
Page 83 and 84:
expansion bus E Glossary The expans
Page 85 and 86:
Modbus NEMA PLC PLI POU PTO M The M
Page 87 and 88:
U unlocated variable An unlocated v
Page 89 and 90:
Modicon M238 Logic Controller Index
Page 91 and 92:
System Variable PLC_R, 16 PLC_W, 18
show all

Library manual M238 system functions | 2 MB - BERGER - POSITEC

Create successful ePaper yourself

Delete template?

Save as template?