M3 XPanded Parameter Guide - Korg

12
Program mode
Source Bus = AUX 1/2
Source Bus = AUX Bus 1/2
Audio Inputs
OSC
Source Bus = Indiv. 1/2
Source Bus = Indiv.1/2
Audio Inputs
OSC
Level Pan
Bus = L/R or IFX1-5
Level Pan
AUX Bus = 1/2
Bus = Indiv.1/2 or IFX1-5
Insert
Effects
Insert
Effects
Insert
Effects
Insert
Effects
Individual Programs, Combi Timbres, Sequencer Tracks,
audio inputs, and Insert Effects can all be routed to the AUX
busses, in addition to their main output/IFX bus settings.
For more information, please see the diagram “Source Bus =
AUX 1/2” on page 12.
Indiv.1/2, Indiv.3/4: This lets you sample the individual
output busses. For more information, please see the diagram
“Source Bus = Indiv. 1/2,” above.
Trigger [Sampling START SW, Note On]
Specifies how sampling will be initiated.
Sampling START SW: Pressing the SAMPLING REC switch
will cause the M3 to enter sampling-standby mode, and
sampling will begin when you press the SAMPLING
START/STOP switch.
Note On: Press the SAMPLING REC switch and then press
the SAMPLING START/STOP switch to enter samplingstandby
mode. Sampling will begin when you play the
keyboard.
Sampling will also begin if a MIDI note-on is received
(instead of playing the keyboard).
Regardless of the settings you’re using, press the
SAMPLING START/STOP switch once again when you’ve
finished sampling. Alternatively, sampling will end
automatically if the specified “Sampling Time” elapses.
Metronome Precount [Off, 4, 8, 3, 6]
This specifies whether the metronome will sound a countdown
before sampling begins. This can be set only if Trigger
is set to Sampling START SW.
Off: Sampling will begin immediately when you press the
SAMPLING START/STOP switch from recording-standby
mode.
4, 8, 3, 6: When you press the SAMPLING START/STOP
switch from recording-standby mode, the metronome will
count the specified number of beats at the (Tempo) tempo,
L/R
Bus
L/R
Bus
AUX
1/2 AUX
3/4
REC
1/2 REC
3/4
Indiv.
1/2 3/4
Indiv.
1/2
3/4
Master
Effects
Master
Effects
Total
Effects
Total
Effects
CLIP !!
CLIP !!
L-Mono
R-Mono Stereo
Sampling
Monitor
L/MONO
R
Sampling
L-Mono
R-Mono Stereo
Monitor
L/MONO
R
AUDIO OUTPUT
HEADPHONES
AUDIO OUTPUT
HEADPHONES
INDIV.1
AUDIO OUTPUT
INDIV.2
and then sampling will begin. If you set this to 4, sampling
will begin on the count of 0 after a pre-count of 4–3–2–1–0.
The output destination and level of the metronome sound
are specified by the menu command Metronome Setup. If
Bus (Output) Select is set to L/R, the metronome will stop
sounding the instant sampling actually begins.
Save to [RAM, MEDIA]
Specifies the destination to which the data will be written
during sampling.
RAM: The sound will be sampled into RAM memory.
A sample written into RAM memory can be heard
immediately in Program mode or Sampling mode. Use the
menu command Select Bank & Smpl No. (Select RAM Bank
& Sample No.) to specify the Sample No. and to make
settings for automatic conversion to a program.
Data written into RAM memory will be lost when the
power is turned off, so you must save it if you want to
keep it.
Note: If Save to is set to RAM, the +12 dB (Sampling 2–1d)
setting will be applied to the sample sampled to RAM. If
+12 dB is on, a one-voice sample will have a playback level
approximately +12 dB higher, so that the level will be the
same during playback as it was while sampling.
If you’ve selected the Auto +12 dB On check box in the
Select Bank & Smpl No. menu command, the +12 dB
setting will automatically be turned on for sampling.
MEDIA: Sample to an external hard disk etc. connected to
the USB A connector.
When you sample, a WAVE file is created on the media. Use
the Select Directory menu command to specify the writingdestination
media and directory.
To open the resulting sample, you can either use Media
mode to load the sample into RAM, or use Select Directory
etc. to select the file and then press the SAMPLING START/
STOP switch.