GAL16V8 - svn

More documents

Recommendations

Info

Simple Mode Logic Diagram 1 2 3 4 5 6 7 8 9 0000 0224 0256 0480 0512 0736 0768 0992 1024 1248 1280 1504 1536 1760 1792 2016 0 4 DIP & PLCC Package Pinouts 8 12 16 20 24 10 28 PTD 2128 2191 Specifications <strong>GAL16V8</strong> OLMC XOR-2048 AC1-2120 OLMC XOR-2049 AC1-2121 OLMC XOR-2050 AC1-2122 OLMC XOR-2051 AC1-2123 OLMC XOR-2052 AC1-2124 OLMC XOR-2053 AC1-2125 OLMC XOR-2054 AC1-2126 OLMC XOR-2055 AC1-2127 SYN-2192 AC0-2193 19 18 17 16 15 14 13 12 11 Select devices have been discontinued. See Ordering Information section for product status.
Absolute Maximum Ratings (1) Supply voltage V CC ...................................... –0.5 to +7V Input voltage applied .......................... –2.5 to V CC +1.0V Off-state output voltage applied ......... –2.5 to V CC +1.0V Storage Temperature ................................ –65 to 150°C Ambient Temperature with Power Applied ........................................ –55 to 125°C 1.Stresses above those listed under the “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress only ratings and functional operation of the device at these or at any other conditions above those indicated in the operational sections of this specification is not implied (while programming, follow the programming specifications). DC Electrical Characteristics 11 Specifications <strong>GAL16V8</strong>D Recommended Operating Conditions Commercial Devices: Ambient Temperature (T A ) ............................... 0 to 75°C Supply voltage (V CC ) with Respect to Ground ..................... +4.75 to +5.25V Industrial Devices: Ambient Temperature (T A ) ........................... –40 to 85°C Supply voltage (V CC ) with Respect to Ground ..................... +4.50 to +5.50V Over Recommended Operating Conditions (Unless Otherwise Specified) SYMBOL PARAMETER CONDITION MIN. TYP. 3 MAX. UNITS VIL Input Low Voltage Vss – 0.5 — 0.8 V VIH Input High Voltage 2.0 — Vcc+1 V IIL 1 Input or I/O Low Leakage Current 0V ≤ VIN ≤ VIL (MAX.) — — –100 μA IIH Input or I/O High Leakage Current 3.5V ≤ VIN ≤ VCC — — 10 μA VOL Output Low Voltage IOL = MAX. Vin = VIL or VIH — — 0.5 V VOH Output High Voltage IOH = MAX. Vin = VIL or VIH 2.4 — — V IOL Low Level Output Current L-3/-5 & -7 (Ind. PLCC) — — 16 mA L-7 (Except Ind. PLCC)/-10/-15/-25 Q-10/-15/-20/-25 — — 24 mA IOH High Level Output Current — — –3.2 mA IOS 2 Output Short Circuit Current VCC = 5V VOUT = 0.5V T A = 25°C –30 — –150 mA COMMERCIAL ICC Operating Power VIL = 0.5V VIH = 3.0V L -3/-5/-7/-10 — 75 115 mA INDUSTRIAL Supply Current ftoggle = 15MHz Outputs Open L-15/-25 — 75 90 mA Q-10/-15/-25 — 45 55 mA ICC Operating Power VIL = 0.5V VIH = 3.0V L -7/-10/-15/-25 — 75 130 mA Supply Current ftoggle = 15MHz Outputs Open Q -20/-25 — 45 65 mA 1) The leakage current is due to the internal pull-up resistor on all pins. See Input Buffer section for more information. 2) One output at a time for a maximum duration of one second. Vout = 0.5V was selected to avoid test problems caused by tester ground degradation. Characterized but not 100% tested. 3) Typical values are at Vcc = 5V and TA = 25 °C Select devices have been discontinued. See Ordering Information section for product status.
Page 1 and 2: Features • HIGH PERFORMANCE E2CMO
Page 3 and 4: Lead-Free Packaging Commercial Grad
Page 5 and 6: Registered Mode In the Registered m
Page 7 and 8: Complex Mode In the Complex mode, m
Page 9: Simple Mode In the Simple mode, mac
Page 13 and 14: AC Switching Characteristics PARAM.
Page 15 and 16: fmax Descriptions LOGIC ARRAY fmax
Page 17 and 18: Power-Up Reset Circuitry within the
Page 19 and 20: Vol (V) Normalized Icc 1 0.75 0.5 0
Page 21 and 22: Vol (V) Normalized Icc 0.5 0.4 0.3
Page 23 and 24: Vol (V) 0.6 0.4 0.2 Vol vs Iol 0 0

GAL16V8 - svn

Create successful ePaper yourself

Delete template?

Save as template?