Master's Thesis - Computer Graphics and Visualization - TU Delft

More documents

Recommendations

Info

Menu Bar Module Library 5.1.2 Module 1) Create a module instance in Canvas Module Categories Figure 5-1 Initial interface Canvas Step 1: In the module categories, click one category you are interested in. Then you will see the modules in this category being shown in the module library. Step 2: In the module library, click the module you are interested in. Then this module is selected. Step 3: Click on the canvas where you want to put the module. (See Figure 5-2, <strong>and</strong> Figure 5-3). - 42 -
(a) Before click. (b) After an item in category list is clicked Figure 5-2 Step 1 in create a module Step 2) click a module Figure 5-3 Step 2 <strong>and</strong> Step 3 in create a module instance Click an item Step 3) click on canvas A new module instance is created There are several buttons on the left side of a module interface. Figure 5-4 shows the names of these buttons. If a button is clicked, the system will show an information level view of a module. More information on the information level views is given in chapter 3. For example, if button “Show View1” is clicked, View1 will be shown (see Figure 3-4). The zoomIn button will show a higher information level than the current one, while the zoomOut button will show a lower information level. - 43 -
Page 1: A Graphical Programming Environment
Page 5 and 6: Preface This project started in Sep
Page 7 and 8: Abstract Culgi stands for Chemistry
Page 9 and 10: Contents Abstract..................
Page 11 and 12: Chapter 1 Introduction Culgi stands
Page 13 and 14: elationship model (see Figure 1-3).
Page 15 and 16: Chapter 2 Requirement Analysis This
Page 17 and 18: loop in which users only need to sp
Page 19 and 20: Primary actor: -Simulation Program
Page 21 and 22: Req04 Select a module in the librar
Page 23 and 24: Chapter 3 Design Models In chapter
Page 25 and 26: also generates the same result as (
Page 27 and 28: 3.3 The Concept Editor 3.3.1 Descri
Page 29 and 30: (a) Step1 Build Box Step2 Create Vi
Page 31 and 32: 3.5.1 Multi view of modules In the
Page 33 and 34: 3.5.2 Various widgets to display a
Page 35 and 36: a correct order. These source codes
Page 37 and 38: Chapter 4 Implementation of the Cul
Page 39 and 40: library. Meanwhile, the interface p
Page 41 and 42: For example, in Figure 3-5(b), the
Page 43 and 44: The Module Editor is a tool for cre
Page 45 and 46: corresponding operations. Figure 4-
Page 47 and 48: The second problem is about how to
Page 49 and 50: sequence. From these approaches, we
Page 51: Chapter 5 Results and Test The prev
Page 55 and 56: instance of the module setDPDEnviro
Page 57 and 58: (a) Make only “Oil” visible (b)
Page 59 and 60: Feedbacks from the novices of Culgi
Page 61 and 62: Chapter 6 Conclusion The goal of th
Page 63 and 64: Chapter 7 Bibliography [1] Craig La
Page 65 and 66: Appendix A. Class Diagrams Figure A
Page 67 and 68: Figure A-4 Class Diagram of “Sequ
Page 69 and 70: Appendix B. Tables Table B-1 Functi
Page 71 and 72: Table B-3 Functionalities of Class
Page 73 and 74: Table B-5 Functionalities of class
Page 75 and 76: Table B-7 Properties of input param
Page 77 and 78: Appendix C. DPD Simulation # DPD Si
Page 79: $plot SetSize 400 400 $plot Load My

Master's Thesis - Computer Graphics and Visualization - TU Delft

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?