Peugeot workshop manual Jet Force (756739) - Scootergrisen

More documents

Recommendations

Info

Reassembly: Re-assemble in the reverse order to dismantling - Tighten the fuel pump using the plug wrench P/N 756716 in order to position the arrow (A) between the marks (B) on the tank - Fit the fuel gauge with a new seal using the gauge wrench P/N 756715 Inspection: Connect the diagnostic tool and check there are no fault codes, erase them if necessary Removal of the starter motor - Disconnect the atmospheric pressure sensor - Disconnect the oil vapour return hose - Remove the air filter housing (2 screws) - Disconnect the battery - Disconnect the starter motor (1) - Remove the starter motor (2) (2 bolts) Note: One of the starter motor fixing bolts is used for the battery engine earth (green wire) Page : 52 125 cc SPECIFIC MISCELLANEOUS WORK Reproduction or translation, even partial, are forbidden without the written consent of <strong>Peugeot</strong> Motocycles
Removal of the rear brake pads or caliper - Remove the pad 2 fixing pins - Remove the caliper 2 fixing bolts - Pull the caliper onto the disc to release the pads (1) - Remove the brake pads Note: After removing the pads, the caliper may be removed from the brake disc. If the caliper is to be changed, the hydraulic control must be slackened off before removal Removal of the suspension arm - Remove the exhaust (3 bolts and 2 bolts nuts) - Remove the wheel spindle nut and the 2 washers - Remove the suspension arm (1) to casing 2 fixing bolts - Remove the suspension arm Note: For re-assembly proceed in reverse order to removal as shown in the diagram 1. Suspension arm 2. Wheel spindle nut 3. Plain washer 4. Bearing flanges 5. Bush 125 cc SPECIFIC MISCELLANEOUS WORK Reproduction or translation, even partial, are forbidden without the written consent of <strong>Peugeot</strong> Motocycles Page : 53
Page 1 and 2: SALES DIVISION NETWORK TECHNICAL IN
Page 3 and 4: CONTENTS Removal of the storage com
Page 5 and 6: CHARACTERISTICS Engine CHARACTERIST
Page 7 and 8: SERVICE SCHEDULE AND COMMISSIONING
Page 9 and 10: TIGHTENING TORQUES Body panels TIGH
Page 11 and 12: INSTRUMENT CLUSTER Instrument clust
Page 13 and 14: INSTRUMENT CLUSTER Changing the dis
Page 15 and 16: CONTROL CABLE AND HARNESS ROUTINGS
Page 17 and 18: Left-hand side 125 cc CONTROL CABLE
Page 19 and 20: LOCATION OF COMPONENTS 50 cc 1. Inj
Page 21 and 22: BODY Location of body components (5
Page 23 and 24: Removal of the storage compartment
Page 25 and 26: - Remove the rear shield (6) (3 scr
Page 27 and 28: Removal of the frame (50 cc) This m
Page 29 and 30: MISCELLANEOUS OPERATIONS Removal of
Page 31 and 32: Removal of the fuel gauge (50 cc) -
Page 33 and 34: Removal of the fuel tank filler rin
Page 35 and 36: Removal of the radiator deflector (
Page 37 and 38: WORKING ON THE ENGINE WITHOUT REMOV
Page 39 and 40: SPECIAL WORK AND PROCEDURES WITHOUT
Page 45 and 46: Removal of the starter motor and/or
Page 47 and 48: ENGINE REMOVAL Removal of the 50 cc
Page 49 and 50: Removal of the fuel injector - Remo
Page 51: Removal of the fuel pump / of the f
Page 55 and 56: Method of fitting the engine mounti
Page 57 and 58: 125 cc SPECIFIC WORK REQUIRING ENGI
Page 59 and 60: Reproduction or translation, even p

Peugeot workshop manual Jet Force (756739) - Scootergrisen

Create successful ePaper yourself

Delete template?

Save as template?