Pacom Hardware Manual.book

More documents

Recommendations

Info

8.2.Mounting Instructions 24 1. Remove Power from the 1057/1058/1058A/1065. 2. Line up mounting holes of the mezzanine card and the standoffs on 1057/1058/1058A/1065, and connect the Mezzanine Card. NOTE The 1057/1058/1058A/1065 has 24pin sockets. Ensure that the mounting holes and standoffs line up. 1 3. Wire mezzanine Cards as required, and power the 1057/1058/1058A/1065. Version 1.0
Pacom Keypad 1061 The Pacom 1061 keypad is an intelligent I/O device that acts as the local user-interface for Pacom controllers. It offers the following features: Manage and control - Up to 8 separate areas within a site. Display - LED display status of areas. Back-lit 2 line x 40 character LCD and adjustable LCD intensity. Programmable customer messages and banner. Communication - Compatible with all Pacom field controllers. Communication over RS485 line (32 device loop addresses). Data encryption optional. On-board inputs and outputs - 2 on-board alarm inputs and 4 on-board control outputs. Access control - Serial connection point for an access control device (Card or proximity reader etc.) and associated I/O devices (LEDs, Door strike etc.). User configurations - Program user IDs (99) and program/ assign user types (13). Automatic baud-detect for fast and easy installation setup. Smart power-save mode. Programmable buzzer frequencies for personal preferences Autobaud detect and self-test. Built-in device tamper switch. Optional shroud. This chapter is written for 1061 revision 05. In This Chapter 9 Installation Guidelines Setup Menu Options 25
Page 1 and 2: Pacom Hardware Installation Guide 8
Page 3 and 4: Contents Pacom Field Controller 105
Page 5: Pacom Two Door Controller 1076 ....
Page 8 and 9: Compliance and Accreditation This i
Page 10 and 11: Technical Specifications Table 1: D
Page 12 and 13: 7 Segment Display 1 6 2 5 4 3 7-Seg
Page 14 and 15: Compliance and Accreditation WARNIN
Page 16 and 17: Technical Specifications Table 1: P
Page 19 and 20: Maintenance Procedures for the Cont
Page 21 and 22: Wiring Information This chapter out
Page 23 and 24: Adding Devices to the Controller Th
Page 25 and 26: The RS232 Port1 or RTU Port connect
Page 27 and 28: Pacom Mezzanine Cards Mezzanine car
Page 29: 8.1.Installation Guidelines EOL SIP
Page 33 and 34: 9.1.Installation Guidelines 1. Open
Page 35 and 36: Technical Specifications Table 2: E
Page 37: Pacom Keypad 1061 Quick Install RES
Page 42 and 43: 11.2.Setup Menu Options The options
Page 44 and 45: 11.3.3. Nidac Keypad Connection Tab
Page 46 and 47: 40 Version 1.0
Page 49 and 50: Pacom Card Reader Interface 1064 Th
Page 51 and 52: 13.1.Installation Guidelines 1. Scr
Page 53 and 54: 13.2.3. Connection via Mosler inter
Page 55 and 56: Table 8: 1064 Input / Output Connec
Page 57: Pacom Card Reader Interface 1064 Qu
Page 62 and 63: A Pacom 1057 RTU can supply up to 2
Page 64 and 65: 58 Version 1.1
Page 67 and 68: Pacom Elevator Controller Card 1065
Page 69 and 70: 17.1.3. Floor Destination Monitorin
Page 71 and 72: Pacom Two Door Controller 1067 The
Page 73 and 74: 18.1.Installation Guidelines 1. If
Page 75 and 76: 18.2.2. Connection via Mosler inter
Page 77 and 78: 18.2.4. Connecting to Binary Keypad
Page 79 and 80: 18.3.In/Out Reader Wiring In/Out re
Page 81:
Pacom Two Door Controller 1067 Quic
Page 84 and 85:
Compliance and Accreditation WARNIN
Page 86 and 87:
Technical Specification Table 1: En
Page 89 and 90:
Pacom Two Door Controller 1076 The
Page 91 and 92:
22.1.Installation Guidelines 1. If
Page 93 and 94:
22.2.2. Connection via Mosler inter
Page 95 and 96:
When connecting card readers for in
Page 97:
Pacom Two Door Controller 1076 Quic
Page 100 and 101:
Compliance and Accreditation WARNIN
Page 102 and 103:
Technical Specification Table 1: Di
show all

Pacom Hardware Manual.book

Create successful ePaper yourself

Delete template?

Save as template?