arcmaster 400 s - Victor Technologies

More documents

Recommendations

Info

ARCMASTER <strong>400</strong> S 11.03 Switching VRD On/Off Switch the machine Off. a) Remove the clear plastic cover from the control panel (see Figure 11). • Lift up the cover so it rests on the top of the unit. • Place a small fl at bladed screw driver between the cover hinge on the front panel. • Gently lift the cover hinge out of the front cover mounting hole. • Remove the control’s clear plastic cover. b) Remove four mounting screws from the control panel (see Figure 12). c) Access the VRD control by gently prying back the front panel controls to reveal the VRD on/off potentiometer (see Figure 12). d) Turning the VRD ON/OFF (see Figure 13). • To turn VRD ON: rote the trim potentiometer (VR1) on the display PCB fully clockwise. When VRD is turned ON check that it operates as per VRD Specifi cations on page 5-13. • To turn VRD OFF: rote the trim potentiometer (VR1) on the display PCB fully counter clockwise. 11-2 Figure 11 VRD ON/OFF Step A CAUTION Do not pull back the front panel with excessive force as this will unplug control PCB. Plugging the control PCB back into the front panel controls can only be achieved by removing the side covers. March 31, 2006
Figure 12 VRD ON/OFF Step B,C ! WARNING ARCMASTER <strong>400</strong> S The VRD ON/OFF trim potentiometer MUST ONLY be positioned fully clockwise OR fully counter clockwise as the VRD function will be unknown for every other position. Figure 13 VRD ON/OFF Step D March 31, 2006 11-3
Page 1 and 2: 400 S ARCMASTER ® INVERTER ARC WEL
Page 3 and 4: ! WARNINGS Read and understand this
Page 5 and 6: ARCMASTER 400 S SECTION 7: BASIC TI
Page 7 and 8: SECTION 1: SAFETY INSTRUCTIONS AND
Page 9 and 10: WARNING CYLINDERS can explode if da
Page 11 and 12: 1.03 Precautions De Securite En Sou
Page 13 and 14: 8. Connectez le câble de soudage l
Page 15 and 16: 2.01 How To Use This Manual This Ow
Page 17 and 18: 2.05 Description ARCMASTER 400 S Th
Page 19 and 20: 3.01 Environment The ARCMASTER 400
Page 21 and 22: ARCMASTER 400 S • Input Power Eac
Page 23 and 24: not entitle the buyer of equipment
Page 26 and 27: ARCMASTER 400 S 4-2 Socket Pin Func
Page 28 and 29: ARCMASTER 400 S 4.03 Weld Parameter
Page 30 and 31: ARCMASTER 400 S 5-2 March 31, 2006
Page 34 and 35: ARCMASTER 400 S 7.05 Shielding Gas
Page 38 and 39: ARCMASTER 400 S 9-2 Warning! Discon
Page 40 and 41: ARCMASTER 400 S 10-2 Description Po
Page 42 and 43: ARCMASTER 400 S 5 Non-metallic part
Page 48 and 49: ARCMASTER 400 S 12-2 E14 error code
Page 50 and 51: ARCMASTER 400 S A-2 - N P R2 + Grou
Page 52 and 53: ARCMASTER 400 S A-4 March 31, 2006
Page 54 and 55: LIMITED WARRANTY This information a
Page 57 and 58: GLOBAL CUSTOMER SERVICE CONTACT INF

arcmaster 400 s - Victor Technologies

Create successful ePaper yourself

Delete template?

Save as template?