arcmaster 400 s - Victor Technologies

More documents

Recommendations

Info

ARCMASTER <strong>400</strong> S iv March 31, 2006
SECTION 1: SAFETY INSTRUCTIONS AND WARNINGS ! WARNING ARCMASTER <strong>400</strong> S PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS KEEP AWAY UNTIL CONSULTING YOUR DOCTOR. DO NOT LOSE THESE INSTRUCTIONS. READ OPERATING/INSTRUCTION MANUAL BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT. Welding products and welding processes can cause serious injury or death, or damage to other equipment or property, if the operator does not strictly observe all safety rules and take precautionary actions. Safe practices have developed from past experience in the use of welding and cutting. These practices must be learned through study and training before using this equipment. Some of these practices apply to equipment connected to power lines; other practices apply to engine driven equipment. Anyone not having extensive training in welding and cutting practices should not attempt to weld. Safe practices are outlined in the American National Standard Z49.1 entitled: SAFETY IN WELDING AND CUTTING. This publication and other guides to what you should learn before operating this equipment are listed at the end of these safety precautions. HAVE ALL INSTALLATION, OPERATION, MAINTENANCE, AND REPAIR WORK PERFORMED ONLY BY QUALIFIED PEOPLE. 1.01 Arc Welding Hazards 10. Ground the workpiece to a good electrical (earth) ground. 11. Do not touch electrode while in contact with the work (ground) circuit. 12. Use only well-maintained equipment. Repair or replace damaged parts at once. 13. In confi ned spaces or damp locations, do not use a welder with AC WARNING output unless it is equipped with a voltage reducer. Use equipment with DC output. ELECTRIC SHOCK can kill. 14. Wear a safety harness to prevent falling if working above fl oor level. 15. Keep all panels and covers securely in place. Touching live electrical parts can cause fatal shocks or severe burns. The electrode and work circuit is electrically live whenever the output is on. The input power circuit and machine internal circuits are also live when power is on. In semiautomatic or automatic wire welding, the wire, wire reel, drive roll housing, and all metal parts touching the welding wire are electrically live. Incorrectly installed or improperly grounded equipment is a hazard. 1. Do not touch live electrical parts. 2. Wear dry, hole-free insulating gloves and body protection. 3. Insulate yourself from work and ground using dry insulating mats or covers. 4. Disconnect input power or stop engine before installing or servicing this equipment. Lock input power disconnect switch open, or remove line fuses so power cannot be turned on accidentally. 5. Properly install and ground this equipment according to its Owner’s Manual and national, state, and local codes. 6. Turn off all equipment when not in use. Disconnect power to equipment if it will be left unattended or out of service. 7. Use fully insulated electrode holders. Never dip holder in water to cool it or lay it down on the ground or the work surface. Do not touch holders connected to two welding machines at the same time or touch other people with the holder or electrode. 8. Do not use worn, damaged, undersized, or poorly spliced cables. 9. Do not wrap cables around your body. WARNING ARC RAYS can burn eyes and skin; NOISE can damage hearing. Arc rays from the welding process produce intense heat and strong ultraviolet rays that can burn eyes and skin. Noise from some processes can damage hearing. 1. Wear a welding helmet fi tted with a proper shade of fi lter (see ANSI Z49.1 listed in Safety Standards) to protect your face and eyes when welding or watching. 2. Wear approved safety glasses. Side shields recommended. 3. Use protective screens or barriers to protect others from fl ash and glare; warn others not to watch the arc. 4. Wear protective clothing made from durable, fl ame-resistant material (wool and leather) and foot protection. 5. Use approved ear plugs or ear muffs if noise level is high. March 31, 2006 1-1
Page 1 and 2: 400 S ARCMASTER ® INVERTER ARC WEL
Page 3 and 4: ! WARNINGS Read and understand this
Page 5: ARCMASTER 400 S SECTION 7: BASIC TI
Page 9 and 10: WARNING CYLINDERS can explode if da
Page 11 and 12: 1.03 Precautions De Securite En Sou
Page 13 and 14: 8. Connectez le câble de soudage l
Page 15 and 16: 2.01 How To Use This Manual This Ow
Page 17 and 18: 2.05 Description ARCMASTER 400 S Th
Page 19 and 20: 3.01 Environment The ARCMASTER 400
Page 21 and 22: ARCMASTER 400 S • Input Power Eac
Page 23 and 24: not entitle the buyer of equipment
Page 26 and 27: ARCMASTER 400 S 4-2 Socket Pin Func
Page 28 and 29: ARCMASTER 400 S 4.03 Weld Parameter
Page 30 and 31: ARCMASTER 400 S 5-2 March 31, 2006
Page 34 and 35: ARCMASTER 400 S 7.05 Shielding Gas
Page 38 and 39: ARCMASTER 400 S 9-2 Warning! Discon
Page 40 and 41: ARCMASTER 400 S 10-2 Description Po
Page 42 and 43: ARCMASTER 400 S 5 Non-metallic part
Page 44 and 45: ARCMASTER 400 S 11.03 Switching VRD
Page 48 and 49: ARCMASTER 400 S 12-2 E14 error code
Page 50 and 51: ARCMASTER 400 S A-2 - N P R2 + Grou
Page 52 and 53: ARCMASTER 400 S A-4 March 31, 2006
Page 54 and 55: LIMITED WARRANTY This information a
Page 57 and 58:
GLOBAL CUSTOMER SERVICE CONTACT INF
show all

arcmaster 400 s - Victor Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?