Whiplash Testing Protocol - Euro NCAP

More documents

Recommendations

Info

Version 3.1 June 2011 Figure 7. H-PM in calibration jig with H-point to arm supports 8. Calibration of the H-PM/HRMD Unit Once the H-PM/HRMD assembly is installed into the jig the following measures (with tolerances) should be taken: 8.1 Adjust the HRMD height probe until it is in contact with the forward surface of the jig vertical support. If the lower surface of the height probe contacts the scale at 0mm (±1mm) it is deemed to be within calibration. If this is not possible then the entire HRMD unit should be checked by the manufacturer (ICBC). 8.2 Adjust the HRMD backset probe to contact the forward surface of the jig vertical support. The indicated backset should read 8cm (±1mm). If this is not possible then the entire HRMD unit should be returned to the manufacturer. 49
Version 3.1 June 2011 Figure 8. HRMD with backset and height calibration 9. Attachment of Torso Angle Measuring Surface 9.1 Measure the trunk of the left hand weight hanger with a digital inclinometer. Figure 9. Measurement being taken of the torso angle at the weight hanger trunk by a digital inclinometer. 9.2 A calibrated Angle Measuring surface block should then be attached to ensure the left hand weight hanger trunk to ensure that an angle of 90 (± 0.3 is indicated). 9.3 If the angle of the left hand weight hanger is not at 90 (± 0.3) then a calibrated and adjusted surface block should be installed in place of the standard item. 50
Page 1 and 2: EUROPEAN NEW CAR ASSESSMENT PROGRAM
Page 3 and 4: CONTENTS 1 INTRODUCTION ...........
Page 5 and 6: 2 DEFINITIONS For the purpose of th
Page 7 and 8: 3 COORDINATE SYSTEM 3.1 Sled Coordi
Page 9 and 10: Version 3.1 June 2011 Figure 1: Sea
Page 11 and 12: 4.6 Seat Position Version 3.1 June
Page 13 and 14: Version 3.1 June 2011 Alternatively
Page 15 and 16: 4.6.2.7 Seat adjustments not set in
Page 17 and 18: 5 H-POINT MACHINE & DUMMY POSITIONI
Page 19 and 20: 5.3.21 When each foot is in its fin
Page 21 and 22: 6 HEAD RESTRAINT POSITIONS 6.1 Head
Page 23 and 24: 6.2.3.1.5.4 If there is no locking
Page 25 and 26: Version 3.1 June 2011 Probe displac
Page 27 and 28: Version 3.1 June 2011 only be under
Page 29 and 30: 7 BioRID ATD REQUIREMENTS The tests
Page 31 and 32: 7.3.3 Legs 7.3.3.1 Remove the jacke
Page 33 and 34: 8 TEST SLED REQUIREMENTS 8.1 Accele
Page 35 and 36: Version 3.1 June 2011 Camera View 1
Page 37 and 38: Version 3.1 June 2011 Figure 16: Vi
Page 39 and 40: 11.3 Upper Neck Shear Force (Fx) an
Page 41 and 42: 11.6 Nkm Calculation The following
Page 43 and 44: values. Maxima for each of the four
Page 45 and 46: Appendix II Version 3.1 June 2011 R
Page 47 and 48: in and out of the head and has grad
Page 49 and 50: 5.4 Adjust the rear Concentric Adju
Page 51: Version 3.1 June 2011 Zero to 4mm g
Page 55 and 56: 11. Checking the H-Point Torque 11.
Page 57 and 58: Appendix III Below is an extract fr
Page 59 and 60: Appendix IV 1. Definitions Version
Page 61 and 62: F 13.1 4.0982 R 16 4.25 G 5 6.00 S
Page 63 and 64: G 17 11.00 O 100 -1.00 H 37 11.00 P
Page 65 and 66: H 15 9.50 T 110.7 0.00 I 15 8.75 U
Page 67 and 68: Seat Tilt - An adjustment that rota
Page 69 and 70: Head Restraint Tilt - An adjustment

Whiplash Testing Protocol - Euro NCAP

Create successful ePaper yourself

Delete template?

Save as template?