DUPREX 5000 Series RF INSTALLATION GUIDE - Galaxy Control ...

More documents

Recommendations

Info

FCC Part 15 Notice of Compliance This device operates under Part 15 of the FCC rules. There are several requirements that must be met to maintain compliance. These devices can only be used with approved antennas. The antennas for these units MUST be mounted at a distance of 20 cm or greater from any nearby persons. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Part 15 COMPLIANCE This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ©2005 Cypress Computer Systems,Inc. • www.cypressworld.com 2/18/05 Page 4
The Cypress Duprex RF is the newest member of the Suprex family of products. The Duprex RF 5000 series supports a wide range of additional features from previous versions of the Suprex RF family. Additional features: --Field configurable channel selection --Diagnostic mode for setup and configuration --“Quiet” RF protocol to conserve bandwidth and power --Field configurable reader formats --Additional indicators for determining operational status of the unit Initial setup and configuration. The Duprex RF unit operates as a matched pair of units that share the same communication channel. Default settings from the factory are for Channel 0 unless specified otherwise by the customer If more than one pair are going to be used at the same site, then they should be set to different channels. There are four dip switches that are used for the RF portion of the Duprex (see quick reference diagram for DIP switch numbers). The first switch is the Setup/Config switch. This switch has multiple functions. With the switch in the OFF position, the unit operates in Normal mode. When the switch is in the ON position, the unit is in the Service / Configuration mode. When switching from Normal to Service / Configuration mode, the unit will reset and then load the current address setting on the DIP switch. While the switch remains in Service / Configuration, the unit will operate using a diagnostic protocol that will show communication activity between the Central and Remote units (The Yellow communication LED will flash rapidly). Once the address is loaded it will be saved in non volatile memory. When switching from Service / Configuration mode to Normal mode, the unit will reset and run with a “Quiet” RF protocol. The address that is saved in memory will be used in operation. This Quiet protocol maintains communication between the Central and Remote units as necessary for I/O, Badge Activity, and Supervision without requiring continuous use of the RF channel. Initial Setup; This manual will cover the basic installation procedure for a typical Duprex RF system. The first step will be to configure and test the units at a bench top location where both the Central and Remote units are close together. This will allow the setup and configuration process to occur with both sides of the operation in view. ©2005 Cypress Computer Systems,Inc. • www.cypressworld.com 2/18/05 Page 5
Page 1 and 2: DUPREX 5000 Series RF INSTALLATION
Page 3: DIP Switch Settings- Quick Referenc
Page 7 and 8: The Duprex RF package should contai
Page 9 and 10: Initial power up Plug in the Remote
Page 11 and 12: The RF units are capable on operati
Page 13 and 14: Mounting the units. A site evaluati
Page 15 and 16: The other mounting method utilizes
Page 17 and 18: Plastic Nut With the units physical

DUPREX 5000 Series RF INSTALLATION GUIDE - Galaxy Control ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?