Tamarin marine paints ltd. - Tambour Paints

More documents

Recommendations

Info

EPOTRAN 400 EPOXy CODE: 660-029 – Epotran 400 Black, 660-033 – Epotran 400 Brown DESCRIPTION: A two component high solid coaltar epoxy coating. Highly resistant to crude oil, sea water, fuel oil and waste water. Epotran 400 is recommended for long term corrosion protection of underwater hull of steel vessels, ballast and crude oil tanks. For new building, maintenance and repair. Other typical areas are concrete in severe corrosive immersed environments, steel buried in aggressive soil, pipelines of steel and concrete, steel and concrete in sewage treatment plants, etc. TECHNICAL DATA: Physical Details: At 25ºC & 65% RH Gloss Flat Colors Black, Brown Specific gravity-Kg/Lt 1.4 Volume Solids 80% Film Thickness – Dry 200 mic. Wet 250 mic. Theoretical coverage 4.0 sqm/lit. Flash Point 26 0 C Drying Time –Touch 7 hours Hard 24 hours Shelf Life 24 months V.O.C. 175 g/liter Application Details: Application Method Airless Spray Brush/Roller Mixing Ratio by Volume 1:1 Quantity of thinner 0-5% 10-15% Recommended Nozzle Orifice 0.026” Recommended Inlet Pressure 5-6 atm Cleaning Thinner 4-100 4-100 Recoating Interval See remarks Potlife 2 hours Drying Time at 150 mic dft: •Winter grade Air Temperature Touch Dry Overcoating Interval Self Antifouling Product Min Max Min 0°C* 10 hours 28 hours 96 hours 5°C* 6 hours 20 hours 72 hours 10°C 12 hours 24 hours 60 hours 20°C 8 hours 16 hours 48 hours 30°C 4 hours 12 hours 48 hours 28
Surface Preparation: New Steel: Abrasive blasting to SA 2.5. For temporary protection a suitable Shopprimer may be used, followed by two coats of 150 mic DFT each, or Epitamarin Solekote Aluminum 100 mic, followed by 2 coats of 150-200 microns each. Repair and maintenance: Remove oil, grease etc with suitable detergent. Remove salt and other contaminators by high pressure fresh water. Clean damaged areas by abrasive blasting. Feather edges to sound and intact areas. Remove dust. Touch up to full film thickness. Concrete: Remove slip agent and other possible contaminants by emulsion washing followed by high pressure hosing with fresh water. Remove scum layer and loose matter to a hard, rough and uniform surface, preferably by abrasive blasting, possibly by other mechanical treatment or acid etching. Apply one coat of Epicatalac Clear, after 4 hours apply 1-2 coats of Epotran 400. Application Condition: Use only where application and curing can proceed at temperature above 7 0 C. The temperature of the surface and that of the paint itself must also be above this limit. For temperature below 7°C use Epotran 400 Winter. If EPOTRAN 400 was exposed to sunlight, Overcoating must be within 36 hours. If interval is exceeded, area must be swept. Areas difficult to cover like edges, corners and welds should be stripe coated before and after spray application. Airless spray equipment: A large pump (min. 45:1) is preferred. Storage and Packing: The product should be kept in a cool and dry condition. Packing: 18 Lit. Remarks: Two coats of 150 mic. each is recommended. Bleeding may occur into subsequent coats. The effect is cosmetic only. Tanks should not be taken into use before Epotran 400 is fully cured. Epotran 400 is for professional use only. The numerical information quoted in the data sheet is subject to normal manufacturing tolerances. Practical covering can vary depending on application conditions, structure and weather conditions. The volume solids figure is the percentage of dry film obtained from a given wet film thickness under specified application rate and conditions. The interval given assumes preparation consistent with good painting practice. Safety Precautions: Refer to P.P.A. 2/1. Handle with care. Before and during use observe all safety labels on packaging and paint containers. Consult <strong>Tamarin</strong> Material Safety Data Sheet. Avoid direct contact with skin and eyes (gloves, goggles, face mask barrier cream, etc.) Harmful or fatal if swallowed. Immediately seek medical assistance if swallowed. Avoid inhalation of possible solvent vapors or paint mist. Apply only in well ventilated areas and ensure that adequate forced ventilation exists when applying paint in confined spaces or when the air is stagnant. Take precautions against the risks of fire and explosives. Basic Safety Precautions: No smoking should be permitted in the area. Observe all precautionary notices on containers. Additional safety information is available on request. The information in this data sheet is given in good faith and to the best of our knowledge. It is subject to revision from time to time, in light of experience and our policy of continues Product development. Since condition of application and service may be beyond our control, no liability can be accepted on basis of this data. 29
Page 2 and 3: TAMARIN MARINE PAINTS LTD.
Page 4 and 5: INTRODUCTION TAMARIN MARINE PAINTS
Page 6 and 7: TAMARIN COMPACT PRIMER CONVENTIONAL
Page 8 and 9: TAMARIN SUPER ALUMINUM 045 CONVENTI
Page 10 and 11: TAMARIN B.T.D/TOPCOAT CONVENTIONAL
Page 12 and 13: TAMARIN SUPER CONVENTIONAL PAINT CO
Page 15 and 16: UNDER WATER
Page 17 and 18: Surface Preparation: Fresh water to
Page 19 and 20: Surface Preparation & Application:
Page 21: Surface Preparation: Surface proper
Page 24 and 25: KSIR 88 EPOXY CODE: 648-007 White 6
Page 26 and 27: EPOGAL EPOXy CODE: 649-050 DESCRIPT
Page 30 and 31: EPITAMARIN ZINC RICH EPOXY EPOXy Co
Page 32 and 33: EPITAMARIN UNISEAL ZN EPOXY CODE: 8
Page 34 and 35: EPITAMARIN EA 9 ALUMINIUM EPOXY COD
Page 36 and 37: EPITAMARIN DIVINEX N.B EPOXY CODE:
Page 38 and 39: EPITAMARIN SOLEKOTE FD MIO GREY EPO
Page 41 and 42: POLYURITANE
Page 43: Surface Preparation: New Building:
Page 46 and 47: EPITAMARIN AQUAPOXY 15M TIE COAT Sp
Page 48 and 49: EPITAMARIN AQUAPOXY TOPCOAT 17 M Sp
Page 50 and 51: EPITAMARIN SOLEKOTE ALUMINUM Specia
Page 52 and 53: EPITAMARIN SOLEKOTE RED/GREY/BLACK
Page 54 and 55: EPITAMARIN AFRAPOXY SF Special epox
Page 56 and 57: TAMAGUARD EN 100 Special epoxy prod
Page 59 and 60: SHOPPRIMERS WELDING PRIMERS
Page 61 and 62: Application Condition: Area should
Page 63 and 64: Surface Preparation: Remove oil, gr
Page 65: Application Condition: Area should
Page 68 and 69: SILICONE ALUMINIUM 540 MIscellaneou
Page 70 and 71: TAMARIN SUPER BOAT VARNISH MIscella
Page 72 and 73: TAMARIN R.C.T (RUST CONVERTER) MIsc
Page 74 and 75: TAMARIN BALLAST COAT MIscellaneous
Page 77 and 78: CHEMICALS
Page 79 and 80:
SPECIFIC TECHNICAL INFORMATION Dens
Page 81 and 82:
TAMARIN RUST REMOVER 674 Chemicals
show all

Tamarin marine paints ltd. - Tambour Paints

Create successful ePaper yourself

Delete template?

Save as template?