Tamarin marine paints ltd. - Tambour Paints

More documents

Recommendations

Info

EPITAMARIN EA 9 ALUMINIUM EPOXY CODE: 842-050 DESCRIPTION: A high quality two component recoatable polyamine anticorrosive and weldable Primer. For use as a holding primer for underwater area and above water line on steel, or a primer for aluminum and fiberglass (G.R.P.) Suitable as a tie coat between coaltar epoxy and antifoulings. Recommended for use as a primer for steel that is constantly in touch with petroleum products, water, chemicals, oils, etc. Suitable as an interior coating for petrol tanks in system EA-5/EA9. This system is approved by the Paint Research Association for interior coating of storage tanks, petrol tanks and fuel tanks. TECHNICAL DATA: Physical Details: At 25ºC & 65% RH Gloss Flat Colors Metallic Red , Red Oxide, Cream Specific gravity-Kg/Liter 1.20 Volume Solids 38% Film Thickness – Dry 70 mic. Wet 180 mic. Theoretical coverage 5.42 sqm/lit. Flash Point 21 0 C Drying Time –Touch 1 hour Hard 24 hours Shelf Life 24 months V.O.C. 530 g/litre Application Details Application Method Airless Spray Brush/Roller Mixing Ratio by Volume 9:1 Quantity of thinner (max. vol) 0-10% (4-100) 0-30% (4-100) * Recommended Nozzle Orifice 0.021” Recommended Inlet Pressure 5 atm Cleaning Thinner 4-100 4-100 Recoating Interval 12 hours Potlife 8 hours Drying Time at 50 mic dft Air Temperature Touch Dry Overcoating Interval Self Min Max 5 0 C 1 hour 24 Indefinite 10 0 C 45 min. 18 Indefinite 20 0 C 30 min. 16 Indefinite 30 0 C 20 min. 12 Indefinite 34
Surface Preparation: As a holding primer: Degreasing, remove weld spatter and smooth weld seams and sharp edges. Blast to SA 2.5 to achieve a profile of 50-70 microns. Apply before oxidation occurs. Area should be clean and dry prior to application.. On aluminum: Blast the area to SA 2.0 On Fiberglass: Sand the area. Make sure area is clean and dry prior to application. Application Condition: Area should be clean and dry prior to application. Temperature should be above the dew point during application. As a welding primer: Do not exceed 20-25 mic DFT. All areas difficult to cover properly by spray application should be stripe coated with a brush, immediately before spray application. Storage and Packing: Store in cool and well ventilated place. Container must be kept tightly closed. Packing: 1 kg, 2.5 Ltr. 5.0 Ltr. 20 Ltr. Remarks: This product will not cure adequately below 0 0 C. * For application with roller on fiberglass paint should be diluted by 30% Thinner 4-100. The numerical information quoted in the data sheet is subject to normal manufacturing tolerances. Practical covering can vary depending on application conditions, structure and weather conditions. The volume solids figure is the percentage of dry film obtained from a given wet film thickness under specified application rate and conditions. The interval given assumes preparation consistent with good painting practice. Safety Precautions: Refer to P.P.A. 2/1. Before and during use observe all safety labels on packaging and paint containers. Consult <strong>Tamarin</strong> Material Safety Data Sheet. Avoid direct contact with skin and eyes. (Gloves, goggles, face mask, barrier cream, etc.) Provide adequate ventilation if product comes in contact with skin wash with warm water and soak. If eyes are contaminated flush with water for 10 minutes and obtain medical attention. Basic Safety Precautions: This product contains flammable materials. Keep away from sparks and open flames. No smoking should be permitted in the area. Observe all precautionary notices on containers. Additional safety information is available on request. The information in this data sheet is given in good faith and to the best of our knowledge. It is subject to revision from time to time, in light of experience and our policy of continues Product development. Since condition of application and service may be beyond our control, no liability can be accepted on basis of this data. 35
Page 2 and 3: TAMARIN MARINE PAINTS LTD.
Page 4 and 5: INTRODUCTION TAMARIN MARINE PAINTS
Page 6 and 7: TAMARIN COMPACT PRIMER CONVENTIONAL
Page 8 and 9: TAMARIN SUPER ALUMINUM 045 CONVENTI
Page 10 and 11: TAMARIN B.T.D/TOPCOAT CONVENTIONAL
Page 12 and 13: TAMARIN SUPER CONVENTIONAL PAINT CO
Page 15 and 16: UNDER WATER
Page 17 and 18: Surface Preparation: Fresh water to
Page 19 and 20: Surface Preparation & Application:
Page 21: Surface Preparation: Surface proper
Page 24 and 25: KSIR 88 EPOXY CODE: 648-007 White 6
Page 26 and 27: EPOGAL EPOXy CODE: 649-050 DESCRIPT
Page 28 and 29: EPOTRAN 400 EPOXy CODE: 660-029 - E
Page 30 and 31: EPITAMARIN ZINC RICH EPOXY EPOXy Co
Page 32 and 33: EPITAMARIN UNISEAL ZN EPOXY CODE: 8
Page 36 and 37: EPITAMARIN DIVINEX N.B EPOXY CODE:
Page 38 and 39: EPITAMARIN SOLEKOTE FD MIO GREY EPO
Page 41 and 42: POLYURITANE
Page 43: Surface Preparation: New Building:
Page 46 and 47: EPITAMARIN AQUAPOXY 15M TIE COAT Sp
Page 48 and 49: EPITAMARIN AQUAPOXY TOPCOAT 17 M Sp
Page 50 and 51: EPITAMARIN SOLEKOTE ALUMINUM Specia
Page 52 and 53: EPITAMARIN SOLEKOTE RED/GREY/BLACK
Page 54 and 55: EPITAMARIN AFRAPOXY SF Special epox
Page 56 and 57: TAMAGUARD EN 100 Special epoxy prod
Page 59 and 60: SHOPPRIMERS WELDING PRIMERS
Page 61 and 62: Application Condition: Area should
Page 63 and 64: Surface Preparation: Remove oil, gr
Page 65: Application Condition: Area should
Page 68 and 69: SILICONE ALUMINIUM 540 MIscellaneou
Page 70 and 71: TAMARIN SUPER BOAT VARNISH MIscella
Page 72 and 73: TAMARIN R.C.T (RUST CONVERTER) MIsc
Page 74 and 75: TAMARIN BALLAST COAT MIscellaneous
Page 77 and 78: CHEMICALS
Page 79 and 80: SPECIFIC TECHNICAL INFORMATION Dens
Page 81 and 82: TAMARIN RUST REMOVER 674 Chemicals

Tamarin marine paints ltd. - Tambour Paints

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?