Tamarin marine paints ltd. - Tambour Paints

More documents

Recommendations

Info

EPITAMARIN ZINC RICH EPOXY EPOXy Code no. 842-100 DESCRIPTION: Epitamarin zinc rich epoxy is a two-component, fast drying, zinc rich epoxy primer, with high zinc content. It cures to a hard wearing and is high weather and corrosion resistant coating. Offers catholic protection of local mechanical damage. Can be used as a long term primer on steel, for epoxy, vinyl polyurethane and acrylic systems, and as a shop primer/primer. Other uses: refineries, port cranes, bridges, piers, offshore platforms etc. On ships and barges: Superstructures, decks, hull, hatch covers etc. Complies with SSPC Paint 20, ISO 12944 part 5. TECHNICAL DATA: Physical Details: At 25ºC & 65% RH Gloss Flat Colors Grey Specific gravity-Kg/Lt 2 Volume Solids 50% Film Thickness – Dry Dry 75 mic Wet 150 mic. Theoretical coverage 6.7 sqm/lit. Flash Point 26 0 C Drying Time –Touch Touch -5-10 minutes Hard 24 hours Shelf Life 12 months V.O.C. 462 g/liter Application Details Application Method Airless Spray Brush/Roller Mixing Ratio by Volume 4:1 Quantity of thinner 0-10% 0-20% Recommended Nozzle Orifice 0.021” Recommended Inlet Pressure 5 atm Cleaning Thinner 4-100 4-100 Recoating Interval See remarks Potlife (20 0 C) 8 hours Drying Time at 50 mic dft Air Temperature Touch Dry Over coating Interval By Epoxy * Min Max 5 0 C 5 hours 24 hours 30 days 10 0 C 2 hours 12 hours 30 days 20 0 C 5-10 min. 4 hours 30 days 30 0 C 4 min. 3 hours 30 days 30
Surface Preparation: New steel – Remove oil and grease with suitable detergent. Remove salt and other contamination by high pressure – fresh water cleaning. Blast in accordance with SA 2.5 SIS 05 5900 – 1967 or ISO 8501-1. Blast to achieve a 25 to 50 mic profiles as determined with a Kean Tator Surface Profile Comparator. Remove abrasive residues and dust from surface. Apply as soon as possible after surface preparation to prevent any contamination. Maintenance – Remove oil and grease with suitable detergent. Remove salt and other contaminations by high pressure – fresh water cleaning. Remove rust and loose material preferably by dry abrasive blasting. Feather edges to sound and intact areas. Dust off residues. Touch up to full film thickness. Minor areas may be tool cleaning. Application Condition: Area should be clean and dry prior to application. Temperature should be above the dew point during application.. All areas difficult to cover properly by spray application should be stripe coated with a brush, immediately before spray application. Stir thoroughly with a mixer to a homogeneous condition. If necessary add up to 5% Thinner 4-100. Storage and Packing: Store in cool and dry condition. Packing: 20 Ltr. Remarks: This product will not cure adequately below 5 0 C. * If the maximum recoating interval is exceeded, roughening of the surface is necessary, to ensure intercoat adhesion. Before recoating, after exposure to contaminated environment, clean surface by high pressure fresh water. Allow to dry. The numerical information quoted in the data sheet is subject to normal manufacturing tolerances. Practical covering can vary depending on application conditions, structure and weather conditions. The volume solids figure is the percentage of dry film obtained from a given wet film thickness under specified application rate and conditions. The interval given assume preparation consistent with good painting practice. Safety Precautions: Refer to P.P.A. 2/1. Before and during use observe all safety labels on packaging and paint containers. Consult <strong>Tamarin</strong> Material Safety Data Sheet. Avoid direct contact with skin and eyes. (Gloves, goggles, face mask, barrier cream, etc.) Provide adequate ventilation If product comes in contact with skin wash with warm water and soak. If eyes are contaminated flush with water for 10 minutes and obtain medical attention. Basic Safety Precautions: This product contains flammable materials. Keep away from sparks and open flames. No smoking should be permitted in the area. Observe all precautionary notices on containers. Additional safety information is available on request. The information in this data sheet is given in good faith and to the best of our knowledge. It is subject to revision from time to time, in light of experience and our policy of continues product development. Since condition of application and service may be beyond our control, no liability can be accepted on basis of this data. 31
Page 2 and 3: TAMARIN MARINE PAINTS LTD.
Page 4 and 5: INTRODUCTION TAMARIN MARINE PAINTS
Page 6 and 7: TAMARIN COMPACT PRIMER CONVENTIONAL
Page 8 and 9: TAMARIN SUPER ALUMINUM 045 CONVENTI
Page 10 and 11: TAMARIN B.T.D/TOPCOAT CONVENTIONAL
Page 12 and 13: TAMARIN SUPER CONVENTIONAL PAINT CO
Page 15 and 16: UNDER WATER
Page 17 and 18: Surface Preparation: Fresh water to
Page 19 and 20: Surface Preparation & Application:
Page 21: Surface Preparation: Surface proper
Page 24 and 25: KSIR 88 EPOXY CODE: 648-007 White 6
Page 26 and 27: EPOGAL EPOXy CODE: 649-050 DESCRIPT
Page 28 and 29: EPOTRAN 400 EPOXy CODE: 660-029 - E
Page 32 and 33: EPITAMARIN UNISEAL ZN EPOXY CODE: 8
Page 34 and 35: EPITAMARIN EA 9 ALUMINIUM EPOXY COD
Page 36 and 37: EPITAMARIN DIVINEX N.B EPOXY CODE:
Page 38 and 39: EPITAMARIN SOLEKOTE FD MIO GREY EPO
Page 41 and 42: POLYURITANE
Page 43: Surface Preparation: New Building:
Page 46 and 47: EPITAMARIN AQUAPOXY 15M TIE COAT Sp
Page 48 and 49: EPITAMARIN AQUAPOXY TOPCOAT 17 M Sp
Page 50 and 51: EPITAMARIN SOLEKOTE ALUMINUM Specia
Page 52 and 53: EPITAMARIN SOLEKOTE RED/GREY/BLACK
Page 54 and 55: EPITAMARIN AFRAPOXY SF Special epox
Page 56 and 57: TAMAGUARD EN 100 Special epoxy prod
Page 59 and 60: SHOPPRIMERS WELDING PRIMERS
Page 61 and 62: Application Condition: Area should
Page 63 and 64: Surface Preparation: Remove oil, gr
Page 65: Application Condition: Area should
Page 68 and 69: SILICONE ALUMINIUM 540 MIscellaneou
Page 70 and 71: TAMARIN SUPER BOAT VARNISH MIscella
Page 72 and 73: TAMARIN R.C.T (RUST CONVERTER) MIsc
Page 74 and 75: TAMARIN BALLAST COAT MIscellaneous
Page 77 and 78: CHEMICALS
Page 79 and 80: SPECIFIC TECHNICAL INFORMATION Dens
Page 81 and 82:
TAMARIN RUST REMOVER 674 Chemicals
show all

Tamarin marine paints ltd. - Tambour Paints

Create successful ePaper yourself

Delete template?

Save as template?