Vol.45 - Protel
Vol.45 - Protel
Vol.45 - Protel
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Service Station<br />
SVS-500AS<br />
SERVICE STATIONS<br />
SVS-500AS<br />
Features<br />
Ceramic heater with integrated sensor<br />
A ceramic heater with built-in sensor has been adopted. During<br />
soldering the temperature will remain stable. The temperature will<br />
recover quickly and there is excellent heat recovery power which<br />
keeps the tip temperature stable.<br />
Variable temperature setting<br />
The temperature can be set variably from 200˚ to 480˚C. This allows<br />
a wide range of soldering to be done from terminals and connectors<br />
to flat ICs.<br />
Zero volt switch circuit<br />
Combined temperature controlled<br />
desoldering unit and soldering unit<br />
ANTI STATIC<br />
AS series<br />
Ceramic<br />
ASSERIES<br />
Heater<br />
temperature<br />
CONTROL<br />
This service station combines a desoldering unit and a<br />
temperature controlled soldering unit in one unit. A powerful<br />
compact pump has a maximum vacuum suction of 600mm Hg<br />
(representative value) that allows easy desoldering of single and<br />
multi-layered PCBs. Both the desoldering unit and the soldering<br />
unit temperature are controlled by the temperature control sensor<br />
feedback system.<br />
SOLDERING UNIT<br />
RoHS<br />
The zero volt switch circuit has been adopted for the heater ON/OFF<br />
control to assure a reduction in noise during the ON/OFF operation.<br />
Service station combining a desoldering unit and a<br />
temperature controlled soldering unit all in one.<br />
SOLDERING UNIT<br />
lDuring soldering the temperature remains stable. lThis unit allows a wide<br />
range of soldering to be done from terminals and connectors to flat ICs.<br />
DESOLDERING UNIT<br />
lBuilt-in powerful and compact twin pump. lWhen the trigger is pulled,<br />
the heater is ON to boost temperature in order to compensate for reducing<br />
nozzle temperature during desoldering. After the trigger is released, the<br />
vacuum pump continues operating automatically for approximately 0.5 seconds<br />
reducing the chance of solder jamming in the nozzle.<br />
Front Panel<br />
Desoldering Unit<br />
TIP/NOZZLE TEMPERATURE RECOVERY POWER<br />
Soldering unit<br />
Desoldering unit<br />
(˚C)500 (˚C) 500<br />
Temp.<br />
400<br />
300<br />
200<br />
100<br />
Temperature rise chart<br />
Work<br />
(Set at 400˚C)<br />
Temp.<br />
400<br />
300<br />
200<br />
100<br />
Temperature rise chart<br />
Work<br />
(Set at 450˚C)<br />
(mmHg)<br />
Vacuum degree chart<br />
600<br />
500<br />
400<br />
300<br />
200<br />
100<br />
The characteristic curve has been<br />
derived with a thermocouple secured on<br />
the tip and melting solder consecutively<br />
on 5 5 5mm PCB land size. Soldering<br />
time is approx. 2 seconds/land.<br />
(Tip used- PX-2RT-B, Nozzle used-<br />
TP-100N-10)<br />
0<br />
1<br />
2<br />
3<br />
4<br />
0<br />
0<br />
5<br />
2 4 6 8 10<br />
1 2 3 4 5<br />
(min.) (min.) (100m sec.)<br />
44-a