RTD/Target Catalog - RTD Embedded Technologies, Inc.

“Accessing the Analog World”
Non-Isolated
Isolated 1500 V
(peak 2 s)
Isolated 500 V
(peak 2 s)
VPWR104
50W
HPWR104
75W
XPWR104
75W
HPWR104plus
83W
ATX104plus
88W
ATX104-Express
88W
IPWR104HR
50W
IPWR104HR
L100W
IPWR104HR
H100W
IATX104plusHR
123W ‡
APWR104HR
50W
APWR106HR
50W
ISA
Bus
PCI
PCIe
Input (Vdc) 8–36 8–30 8–36 8–36 8–36 8–36 9–36 18–36 33–75 18–36 16–50 16–50
Power (W) 50 75 75 83 88 88 50 100 100 118 50 50
5 Vdc Output (A) 10.0 15.0 15.0 10.0 10.0 10.0 10.0 20.0 20.0 15.0 6.0 6.0
5 Vdc STBY (A) 1.0 1.0 2.0
–5 Vdc Output (A) 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1
12 Vdc Output (A) 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 1.17 1.17
–12 Vdc Output (A) 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 1.17 1.17
3.3 Vdc Output (A) 10.0 10.0 10.0 10.0
Max Efficiency (%) 90 88 92 90 90 90 81 88 88 90 72 72
MIL-STD-704, 461
Continuous Output Short Circuit Protection
Reverse Polarity Input Protection (Vdc) – 40 – 40 – 40 – 40 – 40 – 40 – 40 – 40 – 100 – 40 – 100 – 100
Voltage Transient Input Protection (kW) 1.5 † 1.5 † 1.5 † 1.5 ‡ 6.6 † 6.6 † 1.5 † 1.5 † 1.5 † 1.5 † 1.5 † 1.5 †
MIL Standard Input Transient 80V (for 1s)
Over Temp Protection (°C) 100 105 105 100
Remote ON/OFF
ATX Control Signal
Operating Temperature: – 40 to +85°C
†
Peak pulse current (28A) 10 μs, (14A) 1000 μs
UPS25 Battery Backup Controllers
‡
Available only in HiDAN and HiDANplus Systems
The UPS25ER is a flexible PC/104 UPS (Uninterruptible Power Supply) subsystem, designed to work together with RTD’s power supplies to form a reliable UPS system.
The UPS25 routes power to your power supply module from either the main input or from the backup battery during main input power failure. It allows main power interruption
up to 30 minutes at 24 W (with our NiMH battery pack) while still maintaining complete computer operation. While the main supply is over 10 V, the UPS25ER will
charge the backup NiMH/NiCd battery pack using its on-board charger circuitry. Application software can interrogate the UPS status and power states at any time. An
interrupt can be generated when the main power fails and there is a status bit that indicates low battery charge.
Features
• Complete battery backup system for embedded CPUs
• Wide input range 10–40 Vdc
• Charger current limited to 1.2 A
• Battery output: +9.6 V nominal, 1.5 Ah
• Adjustable backup voltage trip level
• Charger modes: fast, top off, and trickle
• Battery temperature and voltage condition monitoring
• Two charger status LEDs
• Software controlled charger operation and diagnostics
• Battery and power disconnect after shutdown
• Fast Charge Termination Methods
• – ∆V/t and ∆T/t
• Maximum temperature, time, and voltage
SK-UPS25ER-1 (NiMH)
• 8 AA NiMH cells: 1500 mAHr
• 30 min. backup at 24 W
• Discharge temp: – 10 to +65°C
• Charge temp: 0 to 40°C
SK-UPS25ER-2 (NiCd)
• 8 AA NiCd cells: 1000 mAHr
• 20 min. backup at 24 W
• Discharge temp: – 20 to +65°C
• Charge temp: +10 to +40°C
RTD Embedded Technologies, Inc. | 2010 Product Guide 19