1992-1996 Dodge Viper RT/10 - Paxton Superchargers

More documents

Recommendations

Info

8. Trim the hood release handle to clear the water cooler as shown in Fig. 9-h. If necessary, drill 1/8" holes in a new location to remount the handle so that its function is not impaired. 3. Install a 90° hose onto the fitting on top of the reservoir and secure with a clamp. (See Fig. 9-j.) TRIM EXCESS HANDLE UP TO THIS POINT Fig. 9-h E. Surge Tank Installation 1. Using thread sealant, install the supplied 1/2"NPT to 3/4" hose barb straight fitting into the side of the surge tank. (See Fig. 9-i.) Fig. 9-i 2. Install the 90° fitting into the bottom of the surge tank so that it points the same direction as the straight fitting. Fig. 9-j / ('92-'95 Shown) 4. Connect the bottom surge tank fitting to the hose elbow installed in the top of the reservoir. (See Fig. 9-l.) Install and tighten a clamp on each connection. 5. Trim and connect a section of the supplied hose from the 120° hose installed on the CAC end of the tank to the straight fitting on the surge tank that is pointed toward the CAC. Secure the CAC end with a clamp. Leave the surge tank end loose until after the system is bled. 6. Plug the open fitting in the surge tank, remove the cap and fill the system with 25%/75% coolant/water mix. Fill the system slowly until it refuses to take more coolant or coolant comes out of the open hose. 7. Uncap the surge tank fitting, connect the open hose to it, and tighten with clamp. 8. Loosely install the plastic cap. P/N: 4809646 ©2006 Paxton Automotive All Rights Reserved, Intl. Copr. Secured 17FEB06 v2.0 92-96Viper(4809646v2.0) 9-4
8.905 1.6 1.462 DRILL THROUGH RADIATOR INLET DUCT 2 x Ø5/16" WATER TANK OUTLINE TO WATER PUMP INLET Fig. 9-k-1 / Water Tank Template ('92-'95 Vehicles) .7 5.3 9-5 P/N: 4809646 ©2006 Paxton Automotive All Rights Reserved, Intl. Copr. Secured 17FEB06 v2.0 92-96Viper(4809646v2.0)
Page 1 and 2: KIT # 1201810 Owner’s Installatio
Page 3 and 4: TABLE OF CONTENTS FORWORD . . . . .
Page 5 and 6: 1992-1996 Dodge Viper Before beginn
Page 7 and 8: S U P E R C H A R G E R S IMPORTANT
Page 9 and 10: Section 1 COMPONENT REMOVAL 1. PREP
Page 11 and 12: Section 2 OIL FEED 2. OIL FEED A. R
Page 13 and 14: Section 3 OIL DRAIN 3. OIL DRAIN A.
Page 15 and 16: Section 4 CRANK PULLEY INSTALLATION
Page 17 and 18: Section 5 REPLACEMENT SHOCK TOWER S
Page 19 and 20: Section 6 SUPERCHARGER MOUNTING BRA
Page 21 and 22: Section 7 ALTERNATOR RELOCATION ASS
Page 23 and 24: Section 8 SUPERCHARGER INSTALLATION
Page 25 and 26: Section 9 CHARGE AIR COOLER INSTALL
Page 27: 5. The supplied yellow wire will be
Page 31 and 32: CHARGE COOLER SURGE TANK WATERCOOLE
Page 33 and 34: Section 10 AIR INLET DUCT INSTALLAT
Page 35 and 36: Section 11 TIMING CONTROLLER INSTAL
Page 37 and 38: Section 12 AUXILIARY FUEL PUMP ASSE
Page 39 and 40: Section 13 FUEL INJECTOR REPLACEMEN
Page 41 and 42: Section 14 FINAL CHECK 14. FINAL CH

1992-1996 Dodge Viper RT/10 - Paxton Superchargers

Create successful ePaper yourself

Delete template?

Save as template?