USER AND INSTALLATION MANUAL - KACO new energy, Inc.

More documents

Recommendations

Info

Wind Speed sensor Wind Speed Sensor figure Wire description VCC (5~24Vdc) GND Signal Target port figure Connect the wires Port num. Port name Specification Wire size 1 WSN 2 WSP Wind Speed signal (0Hz~125Hz) 20AWG (0.518mm2) Page 42
To get the most accurate data from the analog interface, the user must calculate gain and offset. Then the user must change the parameters of the Inverter. The symbols for gain and offset are listed here: M l: lower limit of analog input by sensor. M u: upper limit of analog input by sensor. D l: lower limit of displayed value. D u: upper limit of displayed value. M: input value in range of M l and M u. D: displayed value in range of D l and D u. Gain: G= (D u –D 1) / (M u – M 1) Offset: O = D 1 – (G x M 1) Displayed value: D = (G x M) + O After calculating gain and offset, the user must change the values through the GUI or use the CMT (change the settings in the analog tab located in parameter panel). CAUTION! Voltages > 10Vdc or reversed polarity may lead to damage of the sensor input circuits IMPORTANT! System will show unexpected values if gain and offset are not properly set. Ensure that calculations are exact. Page 43
Page 1 and 2: XP100U-H2/ XP100U-H4 XP83U-H6/ XP90
Page 3 and 4: CAUTION! "CAUTION" indicates a haza
Page 5 and 6: CONTENTS IMPORTANT SAFETY INSTRUCTI
Page 7 and 8: 2. SAFETY Appropriate Usage Any oth
Page 9 and 10: DANGER! During operation, high volt
Page 11 and 12: Regulations concerning the preventi
Page 13 and 14: 3. THE BLUEPLANET INVERTER OVERVIEW
Page 15 and 16: Left, Right and Back Page 15
Page 17 and 18: 4. UNPACKING This section describes
Page 19 and 20: Minimum Workspace Requirements The
Page 21 and 22: Foundation L-bracket surface mount
Page 23 and 24: 6. CONNECTING THE CONDUIT In this s
Page 25 and 26: Using the bottom panel for con
Page 27 and 28: Connection Area D D A: AC Connectio
Page 29 and 30: Grid Connection The inverter is con
Page 31 and 32: PV Connection PV Array is connected
Page 33 and 34: 2 300kcmil All 194 (90℃) copper w
Page 35 and 36: UDIO - User digital input output te
Page 37 and 38: UDIO - User digital output (relay c
Page 39 and 40: RS485-2 Target port figure Connect
Page 41: PT1000 (external temperature) senso
Page 45 and 46: 9. COMMISSIONING DANGER! Electric s
Page 47 and 48: 10. OPENING THE INVERTER DANGER! El
Page 49 and 50: 11. OPERATING STARTUP INSTRUCTIONS
Page 51 and 52: If no fault is present the inverter
Page 53 and 54: Operating start Fault Fault Reset D
Page 55 and 56: ANALOG INTERFACE PARAMETERS Paramet
Page 57 and 58: 13. FAULTS & WARNINGS When a proble
Page 59 and 60: Inv. Over Voltage F10 Over voltage
Page 61 and 62: 14. MAINTENANCE Insulating gloves m
Page 63 and 64: Time intervals for maintenance work
Page 65 and 66: PEBB fan assembly 1. Switch off the
Page 67 and 68: Fault Code Message Warning Descript
Page 69 and 70: F33 F34 F40 F41 F42 F43 F44 Grid Un
Page 71 and 72: Maximum continuous output power 100
Page 73 and 74: 7. Interface Specification Display
Page 75 and 76: 17. CONFIGURATION THE INVERTER BLO
Page 77 and 78: Page 77
Page 79: Page 79

USER AND INSTALLATION MANUAL - KACO new energy, Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?