Download the catalogue - legrand

pour underfloor exemple power : xxxxxxx distribution systems
xxxxxxxx Electrak 28 standard system
pour underfloor exemple power : xxxxxxx distribution systems
xxxxxxxx Electrak 25 low noise system
plug-in key code
plug-in key code
YA5123
JA2123
YF5010
YW5010
JF2010
JW2010
YP5332
JP2332
Technical caracteristics (p. 15)
Technical caracteristics (p. 15)
Conform to BS EN 60 439-1, BS EN 60 439-2 and BS 7671: 2008 IEE
Wiring Regulations
ASTA approved
14
@
Pack Cat.Nos Electrak 28 standard floor busbar system
Standard system with red components
Underfloor system consist of continuous lengths of
power track which are fed from the distribution board
via busbar feed boxes and can be installed in a raised
floor clearance height 48 mm
Busbars
Rated current: 63 A
230/400 VA - 50/60 Hz
300 mm socket centres
Each busbar is equipped with connectors (one male
and one female) at each extremity. Connection of
busbars is made by simply snap fi tting
Access to power is provided along the power track
by simply plugging tap-off units into shuttered
socket outlets
Supplied with fl oor fi xing brackets
Length (m) No. of sockets No. fi xing brackets
1 YA5123 1.2 4 2
1 YA5243 2.4 8 2
1 YA5363 3.6 12 3
Busbar feed boxes
1 YF5010 With T, N and L connector terminals
With Ø25 mm cable conduit fi xing hole
Flexible interlinks
Consist of two busbar connectors (male and female)
Used to connect 2 busbars when changing direction
1 YW5000 Without cable or conduit
1 YW5010 With 1.2 m metal fl exible conduit and cables
1 YW5020 With 2.4 m metal fl exible conduit and cables
Tap-off units
Can be connected directly through the fl oor via
grommet outlets (p. 46) to workstations (p. 48)
Supplied with Ø16 mm fl exible conduit and
T, N and L tap-off connectors
1 YP5332 32 A unfused - length 3 m
1 YP5532 32 A unfused - length 5 m
1 YP5327 13 A fused 543-7 - length 3 m
1 YP5527 13 A fused 543-7 - length 5 m
Conform to BS EN 60 439-1, BS EN 60 439-2 and BS 7671: 2008 IEE
Wiring Regulations
ASTA approved
@
Pack Cat.Nos Electrak 25 low noise (clean earth) floor
busbar system
Standard system with green components
Underfloor system consist of continuous lengths of
power track which are fed from the distribution board
via busbar feed boxes and can be installed in a raised
floor clearance height 48 mm
Busbars
Rated current: 63 A
230/400 VA - 50/60 Hz
300 mm socket centres
Each busbar is equipped with connectors (one male
and one female) at each extremity. Connection of
busbars is made by simply snap fi tting
Access to power is provided along the power track
by simply plugging tap-off units into shuttered
socket outlets
Supplied with fl oor fi xing brackets
Length (m) No. of sockets No. fi xing brackets
1 JA2123 1.2 4 2
1 JA2243 2.4 8 2
1 JA2363 3.6 12 3
Busbar feed boxes
1 JF2010 With T, N, L and clean T connector terminals
With Ø25 mm cable conduit fi xing hole
Flexible interlinks
Consist of two busbar connectors (male and female)
Used to connect 2 busbars when changing direction
1 JW2000 Without cable or conduit
1 JW2010 With 1.2 m metal fl exible conduit and cables
1 JW2020 With 2.4 m metal fl exible conduit and cables
Tap-off units
Can be connected directly through the fl oor via
grommet outlets (p. 46) to workstations (p. 48)
Supplied with Ø16 mm fl exible conduits and
T, N, L and clean T connectors
1 JP2332 32 A unfused - length 3 m
1 JP2532 32 A unfused - length 5 m
1 JP2327 13 A fused 543-7 - length 3 m
1 JP2527 13 A fused 543-7 - length 5 m
Electrak underdesk modules (p. 48)