free flow users guide - PBportal.de

More documents

Recommendations

Info

Technology combines the latest fluid engineering philosophies with real world paintball experience. Free Flow Technology combines usability with “low cycling pressure” to create some of the finest custom paintball guns on the market. Even though we are constantly developing new ideas, the most proven ones are available in our custom Autococker design. The Team Lockout Free Flow Autococker The Free Flow Autococker started as a small way to eliminate ball chopping in the “real world” paintball environment. When paintball manufacturers started making “brittle” paintballs to reduce costly bounced shots, we realized the crucial importance of this paint in top level tournament competition. Sometimes it wasn’t the best team that won the game, it was the team that got a “lucky” bounce that ended up pulling a game out of certain defeat. After using this paint for a short while, we noticed a tendency to chop more balls in the breach from a hard hitting bolt of a half-fed paintball. Incorrect feeding of paint can, sometimes, be eliminated by motorized loaders, shooting slower or just keeping the gun upright. We tried as players to use these methods to our advantage, but it always seemed that the one time you are in the tightest bunker on the field, trying to angle your gun through a hole to make the one game breaking shot, you were almost sure to chop a ball. We then decided that half fed balls are not the only major cause of chopped paint but nearly impossible to avoid in a top level paintball competition. Since the Autococker was already on of the most proven guns available, and it offered on of the lowest “cycling” pressures stock, we began a project that soon became recognized throughout the paintball circuit as the Free Flow Autococker.Teh Free Flow Autococker stared off as just trying to find easy to reduce the pressure of the ram. If we can reduce the pressure in the ram mechanism then the balls couldn’t chop in the breech the pressure moving the bolt would be lower than that needed to crush a paintball. After three full years of design and prototyping, we have designed a custom Autococker that takes this philosophy to a new level. This is the Autococker that you now own. The Team Lockout Free Flow Aoutococker combines all that we have learned, tested and proven in top level paintball into a usable package that effectively drops ”cycling” pressure to less than half of any other gun produced today. Standard Autocockers cycle at approximately 90psi. Most customized Autocockers cycle at roughly the same or higher pressures due to a low “firing” pressure philosophy. Team Lockout Free Flow Autocockers cycle as low as 30psi while keeping the “firing” pressure slightly lower than stock. Getting Started:
This guide will teach you to maintain your Team Lockout Free Flow Autococker. It will also help you diagnose and solve minor problems unique to our low cycling pressure philosophy. A few things need to be mentioned before we begin. 1. It is extremely important to wear safety approved paintball goggles whenever handling a loaded Autococker. Even if the propellant is removed (CO2, HPA, or N 2 ) is removed, enough air may remain inside the secondary regulator to discharge the Autococker. 2. ALWAYS disconnect the propellant and remove all paintballs from the Autococker before performing maintenance or diagnostics. 3. Even though the Tem Lockout Free Flow Autococker is slightly different than the standard Autococker it still functions with the same pattern. All users should be familiar with the current Worr Game Products Autococker Users Manual and must abide by all safety recommendations within that publication. 4. All Team Lockout Free Flow Autocockers come with a lifetime parts and service warranty. This warranty is gun specific not owner specific. If you are not confident with what you see here in this guide – send it to an authorized service center (see page 12) and we’ll service it FREE (you must cover the shipping). Team Lockout Free Flow Autococker Features: This version of out Free Flow Autococker incorporates proven technology from several manufacturers to achieve super low cycling pressures. Functional features: 1. Heavy nylon locking hammer design that eliminates “lug walk” and the loosening of the cocking rod due to vibration. 2. Complete Free Flow Pneumatic kit to transfer large volume, low pressure air efficiently and smoothly (Includes Micro Rock Regulator – still the most adjustable and reliable front end regulator made, WGP’s STO Ram – the best serviceable ram on the market, and our high volume smooth bore “Bullet” 4-way valve – this trigger activated valve has 4 times the flow of any other to aid in rapid transfer of low pressure air to the ram. 3. Custom Free Flow Low Cycle Pressure valve – using the most proven and reliable “WGP” cup seal and guide pin we reduce the spring pressure needed to achieve optimum velocity while improving overall shots per tank by 40%. 4. A softer main spring that is 4 times lighter than any “Nelson” spring – this reduces lug release tension behind the trigger so you can fire the gun without working out your trigger finger. 5. Hand polished trigger internals – smooth as a ball bearing and nickel plated to last a lifetime. 6. Professional 45 Frame V2.01 – the only frame of it’s kind. Allows two trigger ride adjustments, sear tension adjustment, sear angle adjustment, and trigger stop adjustment.
Page 1: This guide is designed to accompany
Page 5 and 6: 9. You made need to make minor adju
Page 7: (excluding shipping) if you do not

free flow users guide - PBportal.de

Create successful ePaper yourself

Delete template?

Save as template?