Taurus ELECTRO manual 472 ENG.pdf - Pipistrel

More documents

Recommendations

Info

32 TAURUS <strong>ELECTRO</strong> www.pipistrel.si Normal procedures REV. 0 Fitting the horizontal tail surfaces Horizontal stabilizer and elevator MUST be united during the following procedure. To fit the horizontal tail surfaces first set the trim handle inside the cockpit to full forward position. Make sure the pins, their holes and bushings have been cleaned and greased! Lift the joint stabilizer and elevator and slide them into position by pushing them backwards. Now use the enclosed “T” key to push the security screw down while spinning it clockwise until the screw is completely tightened. Pull the “T” key out and make sure the safety pin holds the head of the screw, so that eventual unscrewing will not occur. At the end tape the gap between horizontal and vertical tail surfaces and cover the hole on top of the vertical stabilizer with a sticker. Check control deflections for smooth, unobstructed movement. Detaching the horizontal tail surfaces Set the trim handle to full forward position and remove the safety sticker covering the hole on top of the horizontal stabilizer and the tape covering the gab between horizontal and vertical tail surfaces. Now use the enclosed “T” key to push the safety pin screw down while spinning it counter-clockwise until it is completely loose. To detach the horizontal tail unit push it forward using firm palm strokes until the unit pops out. When detached, always place the horizontal tail unit onto a soft surface to prevent damage. Schematic of horizontal tail surfaces (dis)assembly
www.pipistrel.si TAURUS <strong>ELECTRO</strong> 33 Normal procedures REV. 0 Attaching the rudder Bring the rudder close to fuselage and fit it first onto the top and then to the bottom hinge. The rudder must then be fully deflected to one side to provide access to the rudder bolts. Use a selfsecuring, pre-glued M6 nut together with a washer and gently screw them onto the bolt using size 10 spanner. To reach the other rudder bolt deflect the rudder to the opposite direction and repeat the up-stated procedure. With both nuts tightened check full rudder deflections for smooth, unobstructed movement. Detaching the rudder Deflect the rudder to one side fully and unscrew the nut of the bolt with which the rudder is attached to the bottom hinge. This is the bolt located in-between the central bolt (axis of rotation) and the bolt holding the metal ropes. DO NOT touch these two bolts - unscrew the nut of the middle bolt ONLY. Now deflect the rudder to the opposite direction and repeat the up-stated procedure. After both bolts have been unscrewed, lift the rudder and detach it first from the bottom, then from the top hinge. Schematic of rudder (dis)assembly
Page 1 and 2: Flight manual and Maintenance manua
Page 3 and 4: www.pipistrel.si TAURUS ELECTRO 3 R
Page 9 and 10: www.pipistrel.si TAURUS ELECTRO 9 G
Page 11 and 12: www.pipistrel.si 3-view drawing TAU
Page 13 and 14: www.pipistrel.si TAURUS ELECTRO 13
Page 25 and 26: www.pipistrel.si Landing gear failu
Page 31: www.pipistrel.si TAURUS ELECTRO 31
Page 41 and 42: www.pipistrel.si Roundout and touch
Page 49 and 50: www.pipistrel.si Maneuver & gust en
Page 51 and 52: www.pipistrel.si Additional technic
Page 57 and 58: www.pipistrel.si Definitions and ex
Page 59 and 60: www.pipistrel.si Flight mass and c.
Page 67 and 68: www.pipistrel.si Power plant, prope
Page 83 and 84:
www.pipistrel.si Keeping your aircr
Page 85 and 86:
www.pipistrel.si TAURUS ELECTRO 85
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
show all

Taurus ELECTRO manual 472 ENG.pdf - Pipistrel

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?