Ed. 07/2006 - Scotsman

More documents

Recommendations

Info

Service Manual c) REPLACEMENT of ICE-BREAKER BUSH and SCRAPER Stop the scraping roller in a position that enables you to access it from the upper access area. Fig.1 Slacken the two socket head screws behind the icebreaker support (fig.1). Slacken the adjusting screw (fig.2) Remove the support, place in a vice and with a hammer and plastic cylinder, apply pressure until the bush is removed. Fig.2 Fig.3 Insert the new bush with a wooden cylinder or similar to distribute the mechanical pressure during the forced insertion. (fig.3/4). Re-position the upper support fixing it loosely with the socket head screws. Before unscrewing the Fig.4 lower support, the shaft should be secured with an eyebolt (fig.5) so that it does not fall. Fig.5 Repeat the same operation as used for the upper support, tighten all screws Check that the roller rotates freely (without coming into contact with the evaporator); if it is off-axis, proceed by loosening the adjustment screws and adjust as required, (see start-up and adjustment). For the replacement of the ice-breaker follow the same procedure. Slacken the screws on the upper support; remove the roller and the upper and lower supports. The lower support is accessible from the ice outlet. Lower support registration screw lower support - socket head fixing screws 31 Rev. 07/2006
Service manual d) REPLACEMENT OF THERMOSTATIC VALVE / FTL Before replacing the part, check that there is no refrigerant in the evaporator. Proceed with the necessary operations in order to bring the valve / FTL to a state of good working order. ! Maintenance has to be done by qualified personnel and complying to the standards of the country where the machine is installed. e) REPLACEMENT OF DEFLECTOR The lower deflector (a) is fixed onto the V support arms of the rotating shaft and the scraper with two M8 screws (b). The disassembly of the deflector should be carried out from the lower part of the ice outlet by unscrewing the two screws. This will allow removal of the deflector and fitting of replacement. b a a f) REPLACEMENT DEFLECTOR and DRIP TRAY (Untill june 2006) The deflector is manufactured in two parts fixed together with rivets (a). The deflector brush (b) is placed in contact with the deflector and fixed with M8 screws to the V arm of the rotating shaft. a b 32 Rev. 07/2006
Page 1 and 2: Service manual Industrial scale ice
Page 3 and 4: Service manual I. Safety advices Th
Page 5 and 6: Service manual III. A working outli
Page 7 and 8: Service manual A deflector prevents
Page 9 and 10: Service manual Diagram of the refri
Page 11 and 12: Service manual IV. Production Diagr
Page 13 and 14: Service manual EVE200AS EVE300AS 12
Page 15 and 16: Service manual EVE800AS EVE1000AS 1
Page 17 and 18: Service manual EVE2400ASR Model W m
Page 19 and 20: Service manual VI. INSTALLATION a)
Page 21 and 22: Service manual When the machine is
Page 23 and 24: Service manual If the system initia
Page 25 and 26: Service manual To help with the pri
Page 27 and 28: Service manual GEAR REDUCER PROTECT
Page 29 and 30: Service manual SET-UP and WORKING D
Page 31: Service manual a) REPLACEMENT OF GE
Page 35 and 36: Service manual IX. CLEANING and MAI
Page 37 and 38: Service manual 6. ELECTRICAL CONTRO
Page 39 and 40: Service manual 38 Rev. 07/2006
Page 41 and 42: Service manual DIGITAL VOLTMETER/AM
Page 43 and 44: Service manual X. FAULT ANALYSIS Fo
Page 45 and 46: Service manual XI. EXPLODED VIEWS a
Page 47 and 48: Service manual 11 10 3 1 6 14 7 2 5

Ed. 07/2006 - Scotsman

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?