Caution: This document contains mixed page sizes ... - Cummins Onan

More documents

Recommendations

Info

CONTROL BOARD GENERATOR INTAKE COVER O-RING END BELL THROUGH BOLTS (4) (thread the ends with shorter lengths of thread into the adaptor) 10-3 STATOR ASSEMBLY GENERATOR LEAD EXIT AND BRUSH BLOCK ACCESS ROTOR BEARING ROTOR ASSEMBLY GUARD SCREEN DRIVE DISC (assemble with chamfered edge out) ADAPTOR CASTING SLIP RINGS BRUSH BLOCK ASSEMBLY FAN FIGURE 10-1. GENERATOR
GENERATOR SERVICE WARNING Accidental or remote starting can cause severe personal injury or death. Before removing a housing panel or access door, disconnect the negative (−) cable at the battery to prevent the engine from starting. Brushes and Slip Rings Access: Remove the brush block access cover (Figure 4-2) for access to the brush block assembly and slip rings. Checking for Wear: Check brush wear by marking off a piece of wire at 1 inch (25 mm) and inserting it into each of the two holes in the top of the brush block from which the pig tails exit. Replace the brush if the wire can be inserted more than 1 inch (25 mm). (Make sure the wire rests on top of the brush and not on part of the spring.) Cleaning Up Slip Rings: If the slip rings are grooved or pitted, try cleaning them up with a commutator stone while cranking the engine. (Connect the starter motor directly to a battery and the starter solenoid to a remote start switch.) The rotor will have to be removed if the slip ring assembly has to be replaced. Replacing Brush Block: When replacing the brush block assembly, center the brushes on the slip rings before tightening the two mounting screws. Make sure to reconnect the lead marked F1 to the outboard brush and the lead marked F2 to the inboard brush. BRUSH LEAD TERMINAL FIGURE 10-2. BRUSH BLOCK ASSEMBLY 10-4
Page 1 and 2: Caution: This document contains mix
Page 3 and 4: California Proposition 65 Warning D
Page 5 and 6: SECTION PAGE 3. PERIODIC MAINTENANC
Page 7 and 8: SAFETY PRECAUTIONS Thoroughly read
Page 10 and 11: 1. Introduction ABOUT THIS MANUAL T
Page 12 and 13: 2. Operation RECOMMENDED FUEL WARNI
Page 14 and 15: REMOTE CONTROL PANELS There probabl
Page 16 and 17: AUTOMATIC STARTING AND STOPPING The
Page 18: BREAKING IN A NEW ENGINE Proper eng
Page 21 and 22: GENERAL INSPECTION Inspect the gens
Page 23 and 24: MAINTAINING THE BATTERY AND BATTERY
Page 25 and 26: REPLACING THE FUEL FILTER See Table
Page 27 and 28: COOLANT RECOVERY TANK PRESSURE CAP
Page 29 and 30: REMOVING / INSTALLING GENSET See Se
Page 31 and 32: DISASSEMBLING / REASSEMBLING HOUSIN
Page 33 and 34: RADIATOR ACCESS COVER PRIMARY VIBRA
Page 35 and 36: INJECTOR PUMP CONNECTION FUEL FILTE
Page 38 and 39: 7. Exhaust System WARNING Accidenta
Page 40 and 41: 8. Engine Cooling System GENERAL WA
Page 42: OVERFLOW LINE COOLANT RECOVERY TANK
Page 45 and 46: FLYWHEEL LIFTING EYE OIL FILTER OIL
Page 47 and 48: WARNING Accidental or remote starti
Page 50 and 51: 10. Generator WARNING Accidental or
Page 56 and 57: 11. Control WARNING Accidental or r
Page 58 and 59: LOCAL CONTROL COOLANT TEMPERATURE S
Page 62 and 63: TABLE 12-1. TROUBLESHOOTING WARNING
Page 75 and 76: 14. Specifications MODEL: HDKCA HDK
Page 77: 15. Service Checklist After servici
Page 80 and 81: 338-4461 CONTROL WIRING HARNESS A-2
Page 82: Cummins Power Generation 1400 73rd

Caution: This document contains mixed page sizes ... - Cummins Onan

Create successful ePaper yourself

Delete template?

Save as template?