Horizon Seafari Model 450-1800 Owner's Manual - Zanshin

More documents

Recommendations

Info

HROSystems Horizon Seafari Self Contained and Modular Style D. TOOLS REQUIRED FOR INSTALLATION: 1. Of course, not all installations are typical. For this reason, it is recommended to have a full set of mechanic’s electrician’s tools available. However, no special system tools are required for installation. Though not always necessary, a separate DS Meter, available from HRO Systems, and a volt/ohm meter (VOM) are beneficial and useful tools for system installation and initial start-up. E. SPECIAL CONSIDERATIONS: 1. LENGTH OF CONNECTION LINES: • All connection lines should be as short as possible. Increased length causes line-loss from the system. • The connection lines must be as straight as possible with minimum number of fittings. 2. PLACEMENT AND ROUTING OF THE FEED WATER LINE: • Always plumb the line so that all air may naturally bleed from the feed water line. (Excessive bends and elbows in the Feed Line results in pressure loss) • Pressure losses cause inefficiency and shorter prefilter life. 3. SYSTEM FEED INLET • Must be in constant contact with the feed water. • The Horizon Seafari system must receive an uninterrupted supply of air free feed water. • The Inlet Thru Hull Fitting should be dedicated for only the Horizon Seafari R.O. System. • DO NOT use one Thru Hull Fitting for several auxiliary systems. 4. ACCESS FOR MAINTENANCE • Give careful consideration to access to items for maintenance purposes. • Hidden or out of reach items may become forgotten and cause damage to other system components. 5. THE CONTROL PANEL • Must be accessible for operation and viewing. F. DISTANCE BETWEEN COMPONENTS: 1. Inlet Sea Cock Valve [2] through the Pre-filtration and into the inlet of the High Pressure Pump: 12.5 feet of ¾” I.D. (3.8 meters of 19 mm ID) flexible rigid wall tubing is supplied for the plumbing of the feed water line from the Inlet Sea Cock to the Inlet of the High Pressure Pump. Caution must be exercised in extending the length of the feed water line. Feed pressure loss from the Booster Pump causes shorter Pre-filter Element life Keep the distance from the Sea Cock valve to the High Pressure Pump as short and straight as possible. Non-Standard applications may require a larger booster pump. This is determined best by the installer prior to system purchase. 2. Brine Dump Tubing from the System to the Brine Discharge Outlet Fitting [36]: 20 feet of 1/2" OD (15 meters of 12.7 mm OD) tubing is supplied to connect the Brine Discharge Line components. Ensure that no backpressure is present on this line as backpressure causes bypassing at the 3-way product water diversion valve. 3. Product water tubing from the Product Water outlet connection to the Product Water Storage Tank Inlet [46]: 50 feet of 3/8" OD (15 meters of 9.5 mm OD) tubing is supplied for this purpose. Page E - 2
HROSystems Horizon Seafari “Section E” Installation Keep the product water tubing as straight and short as possible. Do Not Install Any Valves in this line. Blockage of the Product Water Line causes extensive damage to the System and the R.O. Membrane Element. G. UNCRATING: SELF-CONTAINED SYSTEMS PACKAGED COMPONENTS (NO OPTIONS SHOWN) INSTALLATION KIT Main System DO NOT DISCARD ANY PACKAGING MATERIAL UNTIL YOU HAVE FOUND AND IDENTIFIED ALL PARTS! Remove the Horizon Seafari system from the shipping crate. Some of the components are loose or separately packaged in the shipping container. Do Not discard any packaging or boxes as they may contain small mounting hardware pieces or small system components. H. HIGH PRESSURE PUMP PREPARATION: Pre-filters Booster Pump MODULAR SYSTEMS PACKAGED COMPONENTS (NO OPTIONS SHOWN) INSTALLATION KIT 1. Remove the orange shipping plug from the highpressure pump and replace with the orange, vented cap. It is very important that the vented cap is installed or pressure builds up within the pump crankcase, which may lead to pump damage 2. Ensure that the pump oil level is at the center of the pump sight glass. Pre-filters Main System High-Pressure Pump The pump oil must be filled with HRO Systems supplied pump oil. Supplied Orange-Colored Vented Oil Fill Cap Must Be Installed Prior to Use. Controller Main Power Enclosure Location of Oil Sight Plug. (Pump oil must be filled to middle of glass prior to operation.) Booster Pump Feed Water Inlet to High Pressure Pump (From Pre-filter or Oil/Water Separator) High Pressure Hose Connection (To R.O. Membrane Inlet) Page E - 3
Page 1: Horizon Seafari Model 450-1800 Owne
Page 4 and 5: This page is intentionally blank.
Page 6 and 7: HROSystems Horizon Seafari Self Con
Page 14 and 15: HRO Systems Horizon Seafari Self Co
Page 46 and 47: Horizon Seafari Self-Contained Comp
Page 68 and 69: Horizon Seafari Modular Components
Page 92 and 93:
HROSystems Horizon Seafari Self Con
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
This page is intentionally blank.
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page L - 2 H2006210002 SEA STRAINER
Page 144 and 145:
ITEM NO. QTY. PART NO. DESCRIPTION
Page 146 and 147:
8 9 11 1 ITEM NO. QTY. PART NO. DES
Page 148 and 149:
ITEM PART NUMBER DESCRIPTION QTY U/
Page 150 and 151:
Page 152 and 153:
Page L - 12 H2221210001 MEMBRANE VE
Page 154 and 155:
5 4 2 ITEM NO. QTY. PART NO. DESCRI
Page 156 and 157:
Page L - 16 B240210011 MVA UPGRADE
Page 158 and 159:
ITEM NO. QTY PART NO. DESCRIPTION 1
Page 160 and 161:
Page L - 20 630 - 1480 GPD BASE MOU
Page 162 and 163:
Page L - 22 B521080001 CHARCOAL FIL
Page 164 and 165:
2 3 1 6 4 5 ITEM NO. Page L - 24 H2
Page 166 and 167:
Page L - 26 B598000002 FRESH WATER
Page 168 and 169:
Page 170 and 171:
HROSystems Horizon Seafari Appendix
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
HROSystems Horizon Seafari Quick Re
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
show all

Horizon Seafari Model 450-1800 Owner's Manual - Zanshin

Create successful ePaper yourself

Delete template?

Save as template?