Cutter Parts - Ppsokc.com

Printer’s Parts Store, Inc. 1708 NW 1 St Oklahoma City, OK 73106
800-375-3787 405-272-0272 405-232-3053 (fax) ppsokc@aol.com ppsokc.com
Cutter Parts
B704 Polar Knife Bolt
For Polar X, XT, E And ED Cutters (409569, 419520).
These Zinc Plated, Grade 12.9, Hex Head Cap Screws Have
A 12mm Diameter Thread. Included With Each Bolt Is A
Heavy 4mm Thick Zinc Plated Washer Made From Heat
Treated 4140 Steel. These Bolts Are 24.5mm Long Below
The Washer. The Washer Is Threaded To Keep It In Place.
B47 Polar Knife Bolt
For Polar 80, 82, 90 & 92 Cutters. These Grade 12.9
Socket Head Cap Screws Have An M10 Thread. They Are
16mm Long (.63") Below The Head And Have A Black
Oxide Finish For Corrosion Resistance
B521 Polar Knife Bolt
For Polar 76, 76 EM And Some 72 (28") Cutters (014116,
021053) Socket Head Cap Screw, 10mm Thread By 21mm
Long (.83") Below The Washer. It Has A 1" Diameter
Washer Which Is 1/4" Thick And Has Been Counter Bored
1/16" Deep To Fit The Head. The Washer Is Held Captive
By A Snap Ring. See Our Part Number B522 For A Shorter
Version Of This Same Bolt.
B522 Polar Knife Bolt
For Polar 55, 66, 71 And Some 72 (28") Cutters (014775,
014776, 021054) Socket Head Cap Screw, 10mm Diameter
Thread By 17mm Long (.67") Below The Washer. It Has A
1" Diameter Washer Which Is 1/4" Thick And Has Been
Counter Bored 1/16" Deep To Fit The Head. The Washer Is
Held Captive By A Snap Ring.
B66 Polar 92 Knife Bolt
For Some Polar 92 Cutters. This Steel, Low Head, Hex
Head Bolt Has A 10mm Thread And Measures 20mm
(.79") Long Below The Washer. The Heavy Steel Washer
Is 1" In Diameter And 1/8" Thick. The Washer Also Has A
Beveled Outer Edge. The Washer Rotates In Place But Is
Held Captive, It Will Not Fall Off.
B705 Prism Knife Bolt
This Hex Head Flange Bolt Fits In Prism 116 And Other
Prism Cutters. It Has An M12 Thread, It Is 24mm (.98")
Long Below The Head, And It Has A 25.4mm (1")
Diameter Washer Built Into It. Both The Bolt And The
Washer Are Machined Out Of A Single Piece Of 4140
Cold Rolled Steel. The Washer Will Not Rotate. The
Oversize Head Measures 19mm (.75") Across. It Has A
Screwdriver Slot Machined Into The Tip Of The Threaded
End To Help Remove It If The Hex Head Wears Down. It
Has A Black Oxide Finish For Corrosion Protection
B671 Prism Knife Bolt
This Hex Head Bolt Has An M12 Thread And Is 22mm
Long Below The Head. It Has A Screwdriver Slot
Machined Into The Tip Of The Threaded End To Help
Remove It If The Hex Head Strips.
B703 Bolt For Sheridan VT Trimmer
Grade 8 Steel Hex Head Bolts, 1/2-13 Threads By 1-31/32"
Long Below The Washer. The Washer Is An Integral Part
Of The Head And Does Not Rotate And Will Not Fall Off.
The Washer Is 1-1/16" In Diameter. Black Oxide Finish For
Corrosion Resistance. Hex Head Measures 3/4" Across The
Flats
B65 Knife Bolts For Itoh Paper Cutters
Socket Head Bolt, 1/2-12 Thread, 1-1/8" Overall Length
Below The Washer. The Captive Washer Is Fixed In Place
And Will Not Fall Off.
S112 Itoh Robocut And Saber 116 Shear Pin
The Main Shank On This Grade 12.9 Steel Socket Head
Cap Screw Shear Bolt Is 8mm (.31") In Diameter, Except
Where It Is Undercut. It Is 55mm (2.16") Long Below The
Head. It Has An M8 Thread. Included With Each Of These
Shear Bolts Is A Zinc Plated Flat Washer And A Zinc
Plated Elastic Stop Nut.
S113 Saber 137 Shear Pin
Grade 12.9 Steel Socket Head Cap Screw Shear Bolt. The
Main Shank Is 10mm (.39") In Diameter, Except Where It
Is Undercut. It Is 55mm (2.16") Long Below The Head. It
Has An M10 Thread. Included With Each Bolt Is A Zinc
Plated Flat Washer And A Zinc Plated Elastic Stop Nut.
S175 Prism 78 & 92 Cutters Shear Bolt
(250600832) This Steel Bolt Is A Direct Replacement For
The Original. The Main Shank Is 12mm (.47") In Diameter
And Is 40mm (1.57") Long Below The Head. It Has An
M12 Thread. Included With Each Bolt Is A Elastic Stop
Nut And A Washer. The Head Is 28mm (1.11") In Diameter
With Two Flats. The Head Is Eccentric To The Shank.
S176 Prism 115 Shear Bolt
This Steel Shear Pin Or Shear Bolt Is A Direct
Replacement For The Original Bolt Supplied By The
Factory. The Main Shank Is 14mm (.55") In Diameter And
Is 40mm (1.57") Long Below The Head. It Has An M14
Thread. Included With Each Of These Shear Bolts Is A
Mating Flange Nut. The Head Is 32mm (1.26") In Diameter
With Two Flats. The Head Is Eccentric To The Shank.
S94 Lawson Pacemaker III & V Shear Bolt
The Main Shank On This Special Socket Head Cap Screw
Is 3/8" In Diameter And Is 2-1/2" Long Below The Head. It
Has A 3/8-16 Thread. An Elastic Stop Nut Is Also Supplied
With Each Of These Shear Bolts.
S108 Harris Seybold Shear Pin
This 2" Diameter By 4-13/16" Long Steel Shear Pin Fits
Many Harris Seybold Paper Cutters. It Is Supplied
Complete With The Insulated Center Short Out Pin
Assembly. This Trips Out The Machine By Blowing A
Fuse When The Pin Breaks During An Overload
Condition. This Is To Prevent The Pull Arm From Cycling
Once The Shear Pin Brakes Apart.
S110 Como Shear Bolt
This Steel Shear Pin Measures 80mm (3.15") Long Below
The Head And It Has A 10mm Thread. The Head Is 22mm
In Diameter (.87") And It Has Two Wrench Flats Machined
Into It. The Main Section Of The Shank Is 10mm In
Diameter.
S201 Wohlenberg 115 Shear Bolt
The Main Alloy Steel Shank Is 16mm (.63") In Diameter
And Is 50mm (1.97") Long Below The Head. It Has An
M16 Thread. The Main Shank Is Cross Drilled For An
Exact Breaking Load. Our Bolts Have Been Tensile Tested
By An Independent Lab And Broke Within 3% Of The
Load Which Is Specified By Wohlenberg.
S202 Wohlenberg 137 Shear Bolt
The Main Alloy Steel Shank Is 16mm (.63") In Diameter
And Is 50mm (1.97") Long Below The Head. It Has An
M16 Thread. The Main Shank Is Cross Drilled For An
Exact Breaking Load. Our Bolts Have Been Tensile Tested
By An Independent Lab And Broke Within 3% Of The
Load Which Is Specified By Wohlenberg.
52
This Is Just A Sample Of Items Available