Cutter Parts - Ppsokc.com

Printer’s Parts Store, Inc. 1708 NW 1 St Oklahoma City, OK 73106
800-375-3787 405-272-0272 405-232-3053 (fax) ppsokc@aol.com ppsokc.com
Cutter Parts
P326 Latch Pin Assembly For False Clamp
This Latch Pin Assembly Locks Into The False
Clamp Pin On Many Different Sizes Of Polar
Paper Cutters. The Overall Length Of The Latch
Pin (Including The Threaded Shank) Is
Approximately 65mm Long (2 9/16" Long). The
Main Latch Area Is 8mm In Diameter. This
Assembly Includes The Latch Pin (206036), The
Spring (205687), The Knurled Knob With Lock
Pin (205527, 200787), And A Self-Locking Nut.
P327 Latch Pin Assembly For False Clamp
This Latch Pin Assembly Locks Into The False
Clamp Pin On The Larger Sizes Of Polar Paper
Cutters. The Overall Length Of The Latch Pin
(Including The Threaded Shank) Is Approximately
70mm Long (2 3/4" Long). The Main Latch Area
Is 8mm In Diameter. This Assembly Includes The
Latch Pin, The Spring (205687), The Knurled
Knob With Lock Pin (205527, 200787), And A
Self-Locking Hex Nut.
PA1025 Pull Arm For Polar 115 CE, 115 El
And Some Early 115 EMC Cutters
(013820, 014128) After Approximately 1984 The
Polar 115 EMC (Sometimes Called The EMC I)
Pull Arm Style Changed To The Type That Uses
A Single Center Shear Bolt. These Are All
Completely New, Non-OEM, Aftermarket Parts.
The Arms Themselves Are Machined Complete
From SAE 1045 Steel. This Assembly Is Supplied
Complete With The Following Parts: Upper
Threaded Arm (Complete With Needle Bearing),
Jam Nut - Left Hand, Turnbuckle Nut, Jam Nut -
Right Hand, Safety Clip, Lower Threaded Arm
(Complete With Internal Bronze Bushing), Lower
Connector (Complete With Bronze Bushing),
Guide Shaft (With Guide Shaft Set Screw And
Jam Nut), Two Shear Bolts With Bolt Nuts
PA1550 Turnbuckle Nut For Newer 115 And
137 Polar Cutters
This Turnbuckle Nut Or Adjusting Nut Is Part Of
The Polar Pull Arm Assembly (Sometimes Called
A Draw Arm). It Fits The Newer Models (EMC
Mon, EMC II, E, Ed, X, And XT) Of Polar 115
And Polar 137 Paper Cutters. After Approx. 1984
The Pull Arms Changed To Using This Style.
These Are All Completely New, Non-OEM,
Aftermarket Parts. The Overall Length Measures
Approx. 4-3/4" Long, It Has An Outside Hex Size
Of 36mm, And It Has Both A Left Hand And A
Right Hand M24 Internal Thread. It Is Machined
Complete From SAE 1045 Steel. (230046)
M530 Seypa Knife Holding Hook
AJ603 Wohlenberg Air Jet Nozzle
It Has A Spring Loaded Stainless Steel Ball.
These Air Jets Are 16mm In Diameter (.630") At
The Large End By 34mm Long (1.34") When
Measured Over The Stainless Steel Ball.
ZJ67219162 Nylon Tipped Thumbscrew That
Locks The Backgauge On Challenge
3/8-16 Thread
1 11/2” Long Under Head
PA1551 Upper Arm For Newer 115 And 137
Polar Paper Cutters
This Upper Arm (230043) Is Part Of The Pull
Arm Assembly (Sometimes Called A Draw Arm).
It Fits The Newer Models (EMC Mon, EMC II, E,
Ed, X, And XT) Of Polar 115 And Polar 137
Paper Cutters. After Approximately 1984 The Pull
Arms Changed To This Style. These Are All
Completely New, Non-OEM, Aftermarket Parts.
The Overall Length Measures Approximately 11-
1/2" And It Has A Left Hand M24 Thread. It Is
Machined Complete From SAE 1045 Steel. This
Is Supplied As Shown In The Photo, Complete
With The Needle Bearing Installed. (207461)
W902 19mm Long Handle Wrench
The Overall Length Of This Long Handle Wrench
(Spanner) Is 12". It Is Used To Fit Down Behind
The Left Side Guide When Changing The Blade
On Some Polar Paper Cutters. These 19mm (3/4")
Wrenches Are Made From Drop Forged Steel
W901 Polar 36mm Open End Wrench
Din 894, Single End, Black Phosphate Coated.
Overall Length Is 11 3/4".
W903 Polar 46mm Open End Wrench
Din 894, Single End, Black Phosphate Coated.
This Wrench Is Normally Used On The Pull Arms
Of Polar 115 Cutters. Overall Length Is 14 3/4".
AJ 701 Perfecta (Seypa) Plastic Air Jet (Nozzle)
It Has A Spring Loaded Stainless Steel Ball To
Control The Air Flow. These Air Jets Are 10mm
In Diameter (.394") And Are 27.5mm Long
(1.08") When Measured Over The Stainless Steel
Ball.
M525 Seypa Knife Leveling Gauge
Made Of Phenolic Material. It Measures
Approximately 33mm Wide X 24mm X 4mm
Thick And It Has Two 5.5mm Wide Slots. Used
On Some Seypa (Perfecta) Paper Cutters.
ZW47 Book Clamp (1 Pair)
"Economy" Style Spine Clamp Or Book Clamp
Sometimes Called Book Trimming Guides For
Cutter Back Gauge., These Clamps Keep Books
And Other Stapled Or Stitched Booklets Flat For
Accurate And Square Cutting By Holding Down
The Spine Of A Book. The Book Clamps Install
On The Guillotine Paper Cutter Back Gauge By
Tightening Them To The Back Gauge Ribs. They
Are Made Of Cast Bronze And Are Sold In Pairs.
ZW46 Book Clamp (1 Pair)
"Challenge" Style Book Clamp Sometimes Called
Book Trimming Guides For Cutter Back Gauge.
These Clamps Keep Books And Other Stapled Or
Stitched Booklets Flat For Accurate And Square
Cutting By Holding Down The Spine Of A Book.
The Book Clamps Install On The Guillotine Paper
Cutter Back Gauge By Tightening Them To The
Back Gauge Ribs. They Are Made Of Cast Bronze
And Are Sold In Pairs.
Pressure Gauge 2”
0-2000 ZJ56479272
0-3000 ZJ56479280
This Is Just A Sample Of Items Available 59