Cutter Parts - Ppsokc.com

Printer’s Parts Store, Inc. 1708 NW 1 St Oklahoma City, OK 73106
800-375-3787 405-272-0272 405-232-3053 (fax) ppsokc@aol.com ppsokc.com
Cutter Parts
S203 Wohlenberg 155 Shear Bolt (7004395)
The Main Alloy Steel Shank Is 16mm (.63") In Diameter
And Is 50mm (1.97") Long Below The Head. It Has An
M16 Thread. The Main Shank Is Cross Drilled For An
Exact Breaking Load. Our Bolts Have Been Tensile Tested
By An Independent Lab And Broke Within 3% Of The
Load Which Is Specified By Wohlenberg.
S204 Wohlenberg 180 & 185 Shear Bolt
The Main Alloy Steel Shank Is 16mm (.63") In Diameter
And Is 50mm (1.97") Long Below The Head. It Has An
M16 Thread. The Main Shank Is Cross Drilled For An
Exact Breaking Load. Our Bolts Have Been Tensile Tested
By An Independent Lab And Broke Within 3% Of The
Load Which Is Specified By Wohlenberg
S205 Wohlenberg 92G & 86 , Lawson Regent Shear Bolt
The Main Thread Is 12mm In Diameter And Measures
45mm Long Below The Head. These Originally Had A
Hole Cross Drilled Through The Side Of The Shank.
However There Was A Recall On The Original Style Bolt
As They Were Too Strong And Would Not Break During
An Overload Condition. This Is The Replacement Style. It
Has A Black Oxide Finish For Corrosion Protection.
S206 Wohlenberg 76 SPM Shear Bolt (9158, 25053)
The Main Thread Is 10mm And Measures 45mm Long
Below The Head. There Is A Drilled Hole Down The
Center Of The Head Into The Shank To Create The Break
Point. This Style Replaces The Old Style With The Cross
Drilled Hole Through The Side Of The Shank. It Has A
Black Oxide Finish For Corrosion Protection.
S207 Wohlenberg 92F Shear Bolt
The Main Thread Is 10mm In Diameter And Measures
40mm (1.57") Long Below The Head. There Is A Necked
Down Notched Area Machined Into The Threaded Part Of
The Bolt. This Is Sometimes Refered To As The "Old
Style" Shear Bolt For These Machines. It Has A Black
Oxide Finish For Corrosion Protection.
S109 Standard Horizon Binder Shear Bolt
Alloy Steel. This 6mm Diameter Alloy Steel Shear Pin Or
Shear Bolt Fits The Standard Horizon Binder. It Is 42mm
Long Below The Head.
S101 Polar 155 EMC & 155 MON Shear Bolt (260465)
Main Shank On This Alloy Steel Shear Bolt Is 3-1/32"
Long Below The Head And Has An M20 (.79") Thread.
The Head Is 1-15/32" In Diameter And 15/32" Thick. The
Head Is Cross Drilled For A Roll Pin Which Is Supplied
Already Installed In The Head. Also Included With Each
Bolt Is A Mating M20 Washer Faced Hex Nut (Collar Nut).
S102 Polar 137 EMC II, 137 MON, 137 X, 137 XT, &
137 ED Shear Bolt (231671, ZA3.423024, 260506)
The Main Alloy Steel Shank Has An M16 (.63") Thread
And Is 2.33" Long Below The Head. Included With Each
Bolt Is A Mating Washer Faced Hex Nut (Collar Nut
231661). The Head Is 1.18" In Diameter And .39" Thick
And Has A Flat On One Side As Shown In The Photo.
S103 Polar 115 EMC II Shear Bolt (231658)
This Alloy Steel Shear Pin Or Shear Bolt Fits The Pull Arm
On Polar 115 EMC II Paper Cutters. The Main Shank Has
An M16 (.63") Thread And Is 2.33" Long Below The Head.
Included With Each Bolt Is A Mating Washer Faced Hex
Nut (Collar Nut 231661). The Head Is 1.18" In Diameter
And .39" Thick And Has A Flat On One Side As Shown.
S104 Polar Most 76, 76 EM, 78, 78 X, & 78 ED Shear
Bolt (027920, 017605)
The Main Alloy Steel Shank Is 1.84" Long Below The
Head. It Has An M12 Thread. Included With Each Bolt Is
A Mating Washer Faced Hex Nut (Collar Nut 233166) And
A Steel Roll Pin (Already Installed). The Head Measures
22mm (.86") In Diameter By 9.5mm (3/8") Thick.
S105 Polar 71 El, 71 CE, 72 EL, 72 CE, 72 CS, & Power
Max 28" Shear Bolt (221987, 220329)
The Main Alloy Steel Shank Is 1.77" Long Below The
Head. It Has An M8 Thread. Included With Each Bolt Is A
Mating Washer Faced Hex Nut (Collar Nut 219563). Both
The Nut And The Head Measure 12mm (.472") Across The
Flats.
S106 Polar 80EL Shear Bolt (208943)
It Has A "D" Style Head, Round With Two Wrench Flats
Machined Into It. The Main Alloy Steel Shank Is 45mm
(1.77") Long Below The Head. It Has An M9 Thread.
Included With Each Bolt Is A Mating Washer Faced Hex
Nut (Collar Nut).
S107 Polar 92 EMC II & 92 ED Steel Shear Bolt
(260469, 017771, 053063)
The Main Shank On This Shear Bolt Or Shear Pin Is 48mm
(1.89") Long Below The Head. It Has An M14 Thread.
Included With Each Pin Is A Mating Washer Faced Hex
Nut (Collar Nut) & A Steel Roll Pin (Already Installed).
The Nut Measures 19mm (.75") Across The Flats.
S91 Polar 82 EL, 82 CE, 86 EL, 86 CE, 90 EL, 90 CE, 92
EL, 92 EMC & 92 CE Shear Bolt (206016)
The Main Shank On This Shear Bolt Measures 9mm
(.354") In Diameter, Except Where It Is Undercut. It Is
54mm (2-1/8") Long Below The Head. It Has An M9
Thread And Two Flats Are Cut On The Sides Of The Head.
Included With Each Bolt Is A Mating Washer Faced Nut.
(Collar Nut Number 205525)
S92 Polar 107 El, 107 ST, Polar 112 El, Polar 115 El,
Polar 115 CE & Polar 115 EMC Shear Bolt (221719)
This Alloy Steel Shear Bolt Is Designed And Engineered
To Replace The Original Factory Overload Shear Bolt. The
Main Shank Is 12mm (.47") In Diameter, Except Where It
Is Undercut. It Is 65mm (2-9/16") Long Below The Head. It
Has An M12 X 1mm Thread With A 17mm Hex Head.
Included With Each Bolt Is A Mating Hex Nut.
S93 Polar 145EL, 150EL, 150CE, Polar 155CE, And
155 EMC (Not 155 EMCII) Steel Shear Bolt (221301)
(Serial Numbers 61896 And Higher)
The Largest Diameter On The Shank On These Shear Pins
Is 14mm (.54"), Except Where It Is Undercut. It Is 80mm
(3.15") Long Below The Head. It Has An M14 Thread. A
Matching Hex Nut Is Also Supplied With Each Of These
Shear Bolts. (Nut Number 205518)
H63 Challenge & Baumfolder Knife Change Handle
The Solid Steel Knife Handle Is 6" Long And Is Machined
From One Solid Piece Of Bar Stock. The Handle Section Is
1" Diameter. The Threaded Section Is 3/8"-16 By 7/8"
Long.
H64-12 Challenge, Lawson, Seybold Knife Change
This Solid Steel Handle Is 6-1/4" Long. The 7/8" Diameter
Shank Is Knurled Over Most Of Its Length For A Solid
Grip. The Thread On This Handle Is 1/2"-12.
This Is Just A Sample Of Items Available 53