Cutter Parts - Ppsokc.com

More documents

Recommendations

Info

Printer’s Parts Store, Inc. 1708 NW 1 St Oklahoma City, OK 73106 800-375-3787 405-272-0272 405-232-3053 (fax) ppsokc@aol.com ppsokc.com Cutter Parts H64-13 Challenge, Lawson, Seybold Knife Handle This Solid Steel Handle Is 6-1/4" Long. The 7/8" Diameter Shank Is Knurled Over Most Of Its Length For A Solid Grip. The Thread Is 1/2"-13 On This Handle. H72 Pivano Knife Changing Handle This Steel Handle Is Machined From One Piece Of Cold Rolled Hex Bar Stock. The Threaded End Has A 12mm X 1.5mm Thread. The Overall Length Is 6" And The Hex Handle Is 5/8" Across The Hex. H69 Triumph Knife Changing Handle This Solid Steel Knife Changing Handle Is 5-3/8" Long And Fits Most Triumph Paper Cutters. The 1/2" Diameter Shank Is Knurled Over Most Of Its Length For A Slip Resistant Grip. It Has A Black Oxide Finish For Corrosion Protection. The Thread Is An M10 X 1.5mm Which Is 20mm Long (.79"). The Pointed End Helps With Blade Alignment During Installation. H70 Triumph Knife Changing Handle This Knife Changing Handle Has A 2-5/8" Long Steel Stud. It Has A 10mm X 1.5mm Thread To Fit Most Triumph Paper Cutters. The Fluted Plastic Hand Grip Is 2-5/8" Long. H65 Most Polar 71, 72, 76, 82 & 92 Knife Handle This Solid Steel Handle Is 5" Long. The 1/2" Diameter Shank Is Knurled Over Most Of Its Length For A Slip Resistant Grip. It Has A Black Oxide Finish For Corrosion Protection. The Thread Is An M10 X 1.5mm Which Is 12mm Long (.47"). DFKNIFE Lifter Polar Knife Changing Handle The Solid Steel Knife Handle Is 6" Long And Is Machined From One Solid Piece Of Bar Stock. The Handle Section Is 1" Diameter. The Thread Is An M10 Which Is 7/8" Long. H66 Most Polar 107, 112, 115, 137, & 155 Knife Handle This Solid Steel Handle Is 5" Long. The 1/2" Diameter Shank Is Knurled Over Most Of Its Length For A Slip Resistant Grip. It Has A Zinc Plated Finish For Corrosion Protection. The Thread Is An M12mm Which Is 12mm Long (.47"). H67 Polar 107, 112, 115, 137 & 155 Knife Handle This Solid Heavy Duty Steel Handle Is 7-1/2" Long. The 1" Diameter Shank Is Knurled Over Most Of Its Length For A Better Grip. The Thread Is An M12mm Which Is 14.5mm Long (.57"). This Heavy Blade Change Handle (Weights Almost 1-1/4 Pounds) Is Machined From One Piece Of Solid Steel Bar Stock And Is Zinc Plated For Corrosion Protection. H68 Polar EL Knife Changing Handle This Handle Has A 7/8" Long, M10 Steel Stud. It Has A 1.5mm Thread Pitch. It Is Used For Knife Changing On Most Polar El Models Of Paper Cutters. The Hand Grip Is Made Of Phenolic Plastic And The Disk Is A Semi-Hard Plastic. K10 Lawson Concentric Knife Change Knob This Cast Aluminum Knob Is 2-1/2" In Diameter, Plus The Thickness Of The Rubber O-Ring. It Has A Fixed Threaded Steel Stud. The Steel Stud Has A 1/2"-13 Thread And Is Mounted In The Center Of The Aluminum Knob. K11 Lawson Eccentric Knife Change Knob This Cast Aluminum Knob Is 2-1/2" In Diameter, Plus The Thickness Of The Rubber O-Ring. It Has A Threaded Steel Stud Which Can Be Rotated By Turning The Steel Cross Pin. The Steel Stud Has A 1/2"-13 Thread And Is Mounted Off Center From The Center Of The Aluminum Disc. This Makes It Possible To Rotate The Knob, Once It Has Been Screwed Into Place, So As To Put Light Pressure Against The Blade Before The Blade Is Loosened In The Blade Carrier. K12 Seybold Knife Changing Handle This Cast Aluminum Knob Is 2-1/2" In Diameter. It Has A Fixed Steel Stud With A 3/8"-16 Thread Which Fits Many Models Of Seybold Paper Cutters. K13 Seybold Knife Changing Knob This Cast Aluminum Knob Is 1-7/8" In Diameter. (Similar To Our Part Number K12) It Has A Fixed Steel Stud With A 3/8"-16 Thread. K14 Polar 90EL, 90CE (Later Models), 92CE, 115CE, & 155CE Knife Changing Handle (010113, 206579) This "Insert And Twist" Type Blade Support Handle Has A Solid Nylon Plastic Body With A Plastic Handle. The Steel Shaft Is 10mm (.39") In Diameter With A Fixed Solid Steel 4mm Diameter Pin For Sliding Down The Slot. For Cutters That Require This Twist Type Blade Support For Use During Knife Changes. K15 Polar 72 CE, 76 EM & Power Max 28 Blade Change Support Handle (010755) The 10mm Diameter Pin On This 10" Long Steel Blade Support Handle Is Inserted In A Hole In The Guide On The Right Side Of The Table. The Nose Of The Blade Support Handle Is Then Rotated Up Against The Front Face Of The Blade. This Helps Keep The Blade In Place As The Knife Bolts Are Removed Or Installed. Changing The Blade Without This Blade Support Tool Creates An Unsafe Condition. Knife Bolt “T” Wrench This Welded All Steel "T" Wrench Has A Quality Steel Hex Key Stock Installed In The End Of Its Shaft Or A Quality Steel Socket Welded To The End Of Its Shaft W71 (3/8" Hex) 17” Long W72 (5/16" Hex) 17” Long W76 (5/16" Hex) 24” Long W73 (8mm Hex) 17” Long W74 (10mm Hex) 24” Long W75 (8mm Hex) 21” Long W77 (10mm Hex) 17” Long W78 (5/8" Socket Hex) 16” Long W79 (11/16" Socket) 16” Long GS-344 Polar 72 CE Guide Shaft Pull Arm This 10mm Diameter Alignment Rod Fits Up The Middle Of The Pull Arm To Prevent It From Flapping Around And Causing Damage When The Shear Bolts Break. It Is Made From Centerless Ground Drill Rod For Maximum Toughness. Overall Length Is Approximately 6-3/4" Long. GS-345 Polar Power Max 28" Guide Shaft Pull Arm This 10mm Diameter Alignment Rod Fits Up Through The Center Of The Pull Arm To Prevent It From Flapping Around And Causing Damage When The Shear Bolts Break. It Is Made From Centerless Ground Drill Rod For Maximum Toughness. Overall Length Is Approximately 6- 3/4" Long. 54 This Is Just A Sample Of Items Available
Printer’s Parts Store, Inc. 1708 NW 1 St Oklahoma City, OK 73106 800-375-3787 405-272-0272 405-232-3053 (fax) ppsokc@aol.com ppsokc.com Cutter Parts GS-346 Polar 80 El Guide Shaft Pull Arm This 11mm Diameter Alignment Rod Fits Up Through The Center Of The Pull Arm To Prevent It From Flapping Around And Causing Damage When The Shear Bolts Break. It Is Made From Centerless Ground Drill Rod For Maximum Toughness. Overall Length Is Approximately 11" Long. GS-347 Polar 82 El Guide Shaft Pull Arm This 11mm Diameter Alignment Rod Fits Up Through The Center Of The Pull Arm To Prevent It From Flapping Around And Causing Damage When The Shear Bolts Break. It Is Made From Centerless Ground Drill Rod For Maximum Toughness. Overall Length Is Approximately 11" Long. GS-348 Polar 92 CE Guide Shaft Pull Arm This 11mm Diameter Alignment Rod Fits Up Through The Center Of The Pull Arm To Prevent It From Flapping Around And Causing Damage When The Shear Bolts Break. It Is Made From Centerless Ground Drill Rod For Maximum Toughness. Overall Length Is Approximately 11" Long. This Rod Uses A Set Screw For Mounting In The Lower Arm. Some Of The 92CE Cutters Used A Roll Pin, Not A Set Screw. If You Need The Roll Pin Style Use Our Part Number GS-349. GS-349 Polar 92 CE Guide Shaft Pull Arm This 11mm Diameter Alignment Rod Fits Up Through The Center Of The Pull Arm To Prevent It From Flapping Around And Causing Damage When The Shear Bolts Break. It Is Made From Centerless Ground Drill Rod For Maximum Toughness. Overall Length Is Approximately 11" Long. This Rod Uses A Roll Pin For Mounting In The Lower Arm. Some Of The 92CE Cutters Used A Set Screw, Not A Roll Pin. If You Need The Set Screw Style Use Our Part Number GS-348. GS-350 Polar 115 CE Guide Shaft Pull Arm This 14mm Diameter Alignment Rod Fits Up The Middle Of The Pull Arm To Prevent It From Flapping Around And Causing Damage When The Shear Bolt Breaks. It Is Made From Centerless Ground Drill Rod For Maximum Toughness. Overall Length Is Approximately 15" Long. It Is Used In Pull Arms Which Have A Set Screw For Locking The Bottom Of The Guide Rod In Place. If Your Pull Arm Uses A Roll Pin To Lock The Bottom Of The Guide Rod In Place Use GS-351. GS-351 Polar 115 CE Guide Shaft Pull Arm This 14mm Diameter Alignment Rod Fits Up The Middle Of The Pull Arm To Prevent It From Flapping Around And Causing Damage When The Shear Bolt Breaks. It Is Made From Centerless Ground Drill Rod For Maximum Toughness. Overall Length Is Approximately 15" Long. It Is Used In Pull Arms Which Have A Roll Pin For Locking The Bottom Of The Guide Rod In Place. If Your Pull Arm Uses A Set Screw To Lock Bottom Of The Guide Rod Use GS-350. GS-352 Polar 115 EL Guide Shaft Pull Arm This 14mm Diameter Alignment Rod Fits Up The Middle Of The Pull Arm To Prevent It From Flapping Around And Causing Damage When The Shear Bolt Breaks. It Is Made From Centerless Ground Drill Rod For Maximum Toughness. Overall Length Is Approximately 15" Long. GS-353 Polar 115 EMC II Guide Shaft Pull Arm This 11mm Diameter Alignment Rod Fits Up The Side Of The Pull Arm To Prevent It From Flapping Around And Causing Damage When The Shear Bolt Breaks. It Is Made From Centerless Ground Drill Rod For Maximum Toughness. Overall Length Is Approximately 13" Long. GS-354 Polar 155 CE & 155 El Guide Shaft Pull Arm This 18mm Diameter Alignment Rod Fits Up The Middle Of The Pull Arm To Prevent It From Flapping Around And Causing Damage When The Shear Bolt Breaks. It Is Made From Centerless Ground Drill Rod For Maximum Toughness. Overall Length Is Approximately 15-3/4" Long. Polar Clutch Handles These "T Wrench" Style Clutch Handles Are Made Of 4140 Steel With Precision Cut Metric Threads. They Have A Black Oxide Finish For Corrosion Protection. These Replace The Original Yellow Plastic Style Handle. These Are Normally Used In Pairs But Are Sold Individually. CH1 71 CE, 72 CE & Power Max 28 (013819) 8mm Threads. CH2 76 EM (017490) 8mm Threads. CH3 82 El 8mm Threads. CH4 90 El 8mm Threads. CH5 92 CE, 92 EMC & 92 ED 8mm Threads. CH6 90 El 8mm Threads. CH7 115 El 10mm Threads. CH8 115 CE, 115 ED & 115 XT 10mm Threads. CH9 115 EMC 10mm Threads. CH10 115 MON, 115 El, 150 El, 155 EMC, 155 MON & 155 CE (010231) 10mm Threads. CH11 137 ED, 137 X & 137 XT 10mm Threads. AH Wohlenberg Blade Leveling Handle This Aluminum Handle Replaces The Original Plastic Blade Leveling Handle On Wohlenberg Paper Cutters. It Has An Aluminum Body With A Stainless Steel And Plastic Handle. B3 Torx Plus Bit This Torx Plus Bit Fits B60, B61, B63 And B64 Blade Bolts For Wohlenberg And Other Paper Cutters. It Accepts A Standard 3/8" Square Ratchet Or Socket Extension. Torx And Torx Plus Bits Are Not Designed To Be Interchangeable. While A Torx Bit Will Also Fit These Bolts, It Is A Loose Fit And Will Strip The Bolt Heads. Never Use A Torx Bit In A Torx Plus Bolt. BS10 Blade Stand Blade Stand For Knife Changing On Larger Polar Paper Cutters. (014569) This Cast Aluminum Blade Stand Has A Smooth Nylon Base. It Is Used For Changing The Blade On Larger Polar Paper Cutters, As Well As Some Other Paper Cutters. It Is Normally Used In Pairs And In Conjunction With Our H67 Knife Changing Tool. Sold Individually. CH9 Prism Clutch Handle Prism 115 Clutch Handle. This 4140 Steel Clutch Handle Is Precision Made With Metric Threads. It Has A Black Oxide Finish For Corrosion Protection. It Fits Prism 115 QZK Paper Cutters. These Are Normally Used In Pairs But Are Sold Individually. CAl10 Pressure Control Pedal Polar Pressure Control Handle Or Pressure Set Handle (010028, 010784, 232637). This Pressure Set Handle Or "Foot Pedal" Fits All Polar Models Which Use This Type Of Pressure Adjusting Handle. It Is Made Of Cast Aluminum, Has A 20mm Diameter Through Hole, And Has A Reference Scale Riveted To The Face. It Is A Direct Replacement For The Original Polar Plastic Handle. It Will Not Crack With Age Like The Original Handles. This Is Just A Sample Of Items Available 55
Page 1 and 2:
800-375-3787 405-272-0272 405-232-3
Page 3 and 4: Printer’s Parts Store, Inc. 1708
Page 53: Printer’s Parts Store, Inc. 1708
Page 105 and 106:
Printer’s Parts Store, Inc. 1708
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
show all

Cutter Parts - Ppsokc.com

Create successful ePaper yourself

Delete template?

Save as template?