Cutter Parts - Ppsokc.com

More documents

Recommendations

Info

Printer’s Parts Store, Inc. 1708 NW 1 St Oklahoma City, OK 73106 800-375-3787 405-272-0272 405-232-3053 (fax) ppsokc@aol.com ppsokc.com Cutter Parts P10 False Clamp Pin Steel False Clamp Pin For Polar Paper Cutters. (206035) 47mm (1.85") Long. Notched As Shown. These False Clamp Pins Are Made In The Usa. P11 False Clamp Pin Steel False Clamp Pin For Polar Cutters, 41.5mm (1.63") Long. (232338) Notched As Shown With Flats Cut On Both Sides Of The Large Diameter Area Of The Shank. This Fits On Newer Cutters. CB10 Carbon Brush For Backgauge Reversing Slip Ring Most Polar Cutters Made Before 1968. The Carbon End Measures 4mm Square X 15mm Long. (.16" Square X .59" Long) CB11 Carbon Brush Carbon Brush For Magnetic Clutch For Polar 71 – 76 El Cutters Built Before 1968. It Measures 8mm X 20mm X 25mm. (.315" X .787" X .984") CB12 Carbon Brush (210610) This Carbon Brush Fits The Magnetic Clutch On Polar 71ST, 72CE, 76EM, 78E, 78ES, 78ED, POLAR 78X, 78XT & 107ST Cutters. It Measures 6.5mm X 10mm X 15mm. (.256" X .394" X .590") FW1 Polar 115 Flywheel Cover (206663). This Clear Plastic Flywheel Cover Is A Direct Replacement For The Original Cover. It Is 10-1/2" In Diameter With Two Drilled Mounting Holes. FW2 Polar 82, 90 & 92 Flywheel Cover This Clear Plastic Flywheel Cover Is A Direct Replacement For The Original Cover. It Is 8-1/4" In Diameter With Drilled Mounting Holes. When Using This Cover In A Polar 82, Two New Mounting Holes Will Have To Be Drilled In This Cover. FW3 Polar 71 & 72 Flywheel Cover (207751) This Rectangular Clear Plastic Flywheel Cover Is A Direct Replacement For The Original Cover. Its Outside Dimensions Are 7-1/4" X 11" With Two Drilled Mounting Holes. W19 Polar Blade Leveling Handle, For 19mm Square Shaft This Handle Is Used On Many Larger Models Of Polar Paper Cutters, Up To And Including The Polar 155. It Is 9" Long And Has A 19mm Square Hole Which Clamps On The Square Blade Leveling Shaft On The Back Side Of The Cutter. BB115CE Polar 115 CE & 115 EMC Blade Back Up Bars (014179) These Steel Backing Bars Or Knife Spacers Are Mounted In The Blade Carrier So That The Second, Lower Set Of Mounting Holes Can Be Used On The Blade When The Blade Has Been Sharpened Down To Half Of Its Original Size. The Socket Head Cap Screws Are Secured In The Blade Spacers. The 12mm Screws Will Rotate But Will Not Fall Out. The Bars Are 15-3/4" Long And Are Ground On Their Top And Bottom Surfaces For An Exact Fit. Sold In Pairs. BB115EL Polar 112 EL & 115 EL Blade Back Up Bars (207455) These Are Mounted In The Blade Carrier So That The Second, Lower Set Of Mounting Holes Can Be Used On The Blade When The Blade Has Been Sharpened Down To Half Of Its Original Size. The Socket Head Cap Screws Are Secured In The Blade Spacers. The 8mm Screw Will Rotate But Will Not Fall Out. The Bars Are 15-3/4" Long And Are Ground On Their Top And Bottom Surfaces For An Exact Fit. They Are Sold In Pairs. G102 Polar 115 EL, 115 CE (Early Models), 137 & 155 Blade Setting Gauge (013747) This Blade Setting Gauge Is Used To Set The Height Of The Blade During Blade Changes. See Our Part Number G101 For The Gauge Used On Smaller Polar Cutters. G101 Blade Setting Gauge For Polar 82 & 92 (013746) This Blade Setting Gauge Is Used To Set The Height Of The Blade During Blade Changes. See G102 For Gauge Used On Larger Cutters. BS-2245 KIT Blade Shim Support Kit (2 Hole) These 2-Hole Blade Shims Or Blade Supports Are Used In Some Polar EMC Paper Cutters And Some Polar 76EM Paper Cutters. They Are Sold As A Kit Which Includes The Following Parts: (2) Plastic Shim Or Support (230056) (2) Double Sided Adhesive Shim (4) Plastic Flat Head Screw (201681) Their Overall Length Is Approximately 127mm Long (5" Long) By Approximately 40mm Wide (1-9/16" Wide). The Tapered Screw Mounting Holes Are Spaced Approximately 100mm (3- 15/16") Apart. Note That Some Polar EMC Machines Take A Shorter 2-Hole Shim. Be Sure To Measure The Length Of Your Existing Shims Before Ordering. BS-2250 KIT Blade Shim Support Kit (3 Hole) These Blade Shims Or Blade Clamp Supports Are Used In Polar EMC Paper Cutters. They Fit The Polar 115 EMC, Polar 137 EMC, And The Polar 155 EMC Paper Cutters. They Are Sold As A Kit Which Includes The Following Parts: (2) Plastic Shim Or Support (224904) (2) Double Sided Adhesive Shim (224910) (6) Plastic Flat Head Screw (201681) Their Overall Length Is Approximately 177mm Long (7" Long) By Approximately 40mm Wide (1-9/16" Wide). The Tapered Screw Mounting Holes Are Spaced Approximately 76mm (3") Apart. P325 Polar 72 CE Latch Pin Assembly For False Clamp The Overall Length Of The Latch Pin (Including The Threaded Shank) Is Approximately 43mm Long (1 3/4" Long). It Is 8mm In Diameter At The Latching End. This Assembly May Also Fit Some Of The Other Smaller Sizes Of Polar Cutters, Such As The Powermax 28. This Assembly Includes The Latch Pin (216198), The Spring (207788), The Knurled Knob With Lock Pin (205527, 200787), And A Self-Locking Hex Nut. 58 This Is Just A Sample Of Items Available
Printer’s Parts Store, Inc. 1708 NW 1 St Oklahoma City, OK 73106 800-375-3787 405-272-0272 405-232-3053 (fax) ppsokc@aol.com ppsokc.com Cutter Parts P326 Latch Pin Assembly For False Clamp This Latch Pin Assembly Locks Into The False Clamp Pin On Many Different Sizes Of Polar Paper Cutters. The Overall Length Of The Latch Pin (Including The Threaded Shank) Is Approximately 65mm Long (2 9/16" Long). The Main Latch Area Is 8mm In Diameter. This Assembly Includes The Latch Pin (206036), The Spring (205687), The Knurled Knob With Lock Pin (205527, 200787), And A Self-Locking Nut. P327 Latch Pin Assembly For False Clamp This Latch Pin Assembly Locks Into The False Clamp Pin On The Larger Sizes Of Polar Paper Cutters. The Overall Length Of The Latch Pin (Including The Threaded Shank) Is Approximately 70mm Long (2 3/4" Long). The Main Latch Area Is 8mm In Diameter. This Assembly Includes The Latch Pin, The Spring (205687), The Knurled Knob With Lock Pin (205527, 200787), And A Self-Locking Hex Nut. PA1025 Pull Arm For Polar 115 CE, 115 El And Some Early 115 EMC Cutters (013820, 014128) After Approximately 1984 The Polar 115 EMC (Sometimes Called The EMC I) Pull Arm Style Changed To The Type That Uses A Single Center Shear Bolt. These Are All Completely New, Non-OEM, Aftermarket Parts. The Arms Themselves Are Machined Complete From SAE 1045 Steel. This Assembly Is Supplied Complete With The Following Parts: Upper Threaded Arm (Complete With Needle Bearing), Jam Nut - Left Hand, Turnbuckle Nut, Jam Nut - Right Hand, Safety Clip, Lower Threaded Arm (Complete With Internal Bronze Bushing), Lower Connector (Complete With Bronze Bushing), Guide Shaft (With Guide Shaft Set Screw And Jam Nut), Two Shear Bolts With Bolt Nuts PA1550 Turnbuckle Nut For Newer 115 And 137 Polar Cutters This Turnbuckle Nut Or Adjusting Nut Is Part Of The Polar Pull Arm Assembly (Sometimes Called A Draw Arm). It Fits The Newer Models (EMC Mon, EMC II, E, Ed, X, And XT) Of Polar 115 And Polar 137 Paper Cutters. After Approx. 1984 The Pull Arms Changed To Using This Style. These Are All Completely New, Non-OEM, Aftermarket Parts. The Overall Length Measures Approx. 4-3/4" Long, It Has An Outside Hex Size Of 36mm, And It Has Both A Left Hand And A Right Hand M24 Internal Thread. It Is Machined Complete From SAE 1045 Steel. (230046) M530 Seypa Knife Holding Hook AJ603 Wohlenberg Air Jet Nozzle It Has A Spring Loaded Stainless Steel Ball. These Air Jets Are 16mm In Diameter (.630") At The Large End By 34mm Long (1.34") When Measured Over The Stainless Steel Ball. ZJ67219162 Nylon Tipped Thumbscrew That Locks The Backgauge On Challenge 3/8-16 Thread 1 11/2” Long Under Head PA1551 Upper Arm For Newer 115 And 137 Polar Paper Cutters This Upper Arm (230043) Is Part Of The Pull Arm Assembly (Sometimes Called A Draw Arm). It Fits The Newer Models (EMC Mon, EMC II, E, Ed, X, And XT) Of Polar 115 And Polar 137 Paper Cutters. After Approximately 1984 The Pull Arms Changed To This Style. These Are All Completely New, Non-OEM, Aftermarket Parts. The Overall Length Measures Approximately 11- 1/2" And It Has A Left Hand M24 Thread. It Is Machined Complete From SAE 1045 Steel. This Is Supplied As Shown In The Photo, Complete With The Needle Bearing Installed. (207461) W902 19mm Long Handle Wrench The Overall Length Of This Long Handle Wrench (Spanner) Is 12". It Is Used To Fit Down Behind The Left Side Guide When Changing The Blade On Some Polar Paper Cutters. These 19mm (3/4") Wrenches Are Made From Drop Forged Steel W901 Polar 36mm Open End Wrench Din 894, Single End, Black Phosphate Coated. Overall Length Is 11 3/4". W903 Polar 46mm Open End Wrench Din 894, Single End, Black Phosphate Coated. This Wrench Is Normally Used On The Pull Arms Of Polar 115 Cutters. Overall Length Is 14 3/4". AJ 701 Perfecta (Seypa) Plastic Air Jet (Nozzle) It Has A Spring Loaded Stainless Steel Ball To Control The Air Flow. These Air Jets Are 10mm In Diameter (.394") And Are 27.5mm Long (1.08") When Measured Over The Stainless Steel Ball. M525 Seypa Knife Leveling Gauge Made Of Phenolic Material. It Measures Approximately 33mm Wide X 24mm X 4mm Thick And It Has Two 5.5mm Wide Slots. Used On Some Seypa (Perfecta) Paper Cutters. ZW47 Book Clamp (1 Pair) "Economy" Style Spine Clamp Or Book Clamp Sometimes Called Book Trimming Guides For Cutter Back Gauge., These Clamps Keep Books And Other Stapled Or Stitched Booklets Flat For Accurate And Square Cutting By Holding Down The Spine Of A Book. The Book Clamps Install On The Guillotine Paper Cutter Back Gauge By Tightening Them To The Back Gauge Ribs. They Are Made Of Cast Bronze And Are Sold In Pairs. ZW46 Book Clamp (1 Pair) "Challenge" Style Book Clamp Sometimes Called Book Trimming Guides For Cutter Back Gauge. These Clamps Keep Books And Other Stapled Or Stitched Booklets Flat For Accurate And Square Cutting By Holding Down The Spine Of A Book. The Book Clamps Install On The Guillotine Paper Cutter Back Gauge By Tightening Them To The Back Gauge Ribs. They Are Made Of Cast Bronze And Are Sold In Pairs. Pressure Gauge 2” 0-2000 ZJ56479272 0-3000 ZJ56479280 This Is Just A Sample Of Items Available 59
Page 1 and 2:
800-375-3787 405-272-0272 405-232-3
Page 3 and 4:
Printer’s Parts Store, Inc. 1708
Page 5 and 6:
Page 7 and 8: Printer’s Parts Store, Inc. 1708
Page 57: Printer’s Parts Store, Inc. 1708
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
show all

Cutter Parts - Ppsokc.com

Create successful ePaper yourself

Delete template?

Save as template?