Download - Tech-Rentals

General Industrial & Process Management
www.techrentals.com.au
Industrial Process Calibrators cont’d.
Industrial Process Calibrators cont’d.
Druck DPI610-20IS 20Bar Pressure Calibrator
DRU,DPI610-20IS
MY
Ranges -1 to 20Bar. Accuracy 0.025% fs all ranges. Integral combined
pressure/vacuum pump. Dual readout: input & output. 4 to 20mA loop test:
auto step and ramp. RS232 interface and fully documenting version. Remote
pressure sensors. Intrinsically safe version.
Druck DPI610-400-NATA 400Bar Pressure Calibrator
DRU,DPI610-400-NATA (4758)
AU
DRU,DPI610-400
MY
Hydraulic pressure calibrator including pump and current voltage standard.
Pressure range 0 to 400Bar ±0.025%fs. Voltage input 50VDC, ±0.05%rdg,
±0.004%fs. Current input 55mA, ±0.05%rdg, ±0.004%fs. Temperature -10 to
40ºC ±1ºC (ambient) switch open/closed. Voltage output 10VDC ±0.1% or 24V
±5%. Current output 0 to 24mA, ±0.05% rdg, ±0.01%fs. Data logger stores
up to 10,000 values. mA ramp configurable. Pressure port G 1/8” (f), includes
flexible hose kit. Pump includes screw adjustment.
Druck DPI615-20-NATA 20Bar
Pressure Calibrator
DRU,DPI615-20-NATA (4756)
AU
Pneumatic pressure calibrator including pump and
current voltage standard. Pressure range 0 to 20Bar
±0.025% FS. Voltage input ±50VDC ±0.05% rdg
± 0.004% FS. Current input ±55mA ±0.05%rdg
±0.004%FS. Temperature -10 to 40ºC ±1ºC (ambient)
switch open/closed. Voltage output 10VDC ±0.1% or
24V ±-5%. Current output 0 to 24mA ±0.05%rdg
±0.01%FS. Data logger stores upto 10,000 values. mA ramp configurable.
Pressure port G 1/8 female, includes flexible hose. Pump includes screw
adjustment.
Druck PV411A Multifunction Hand Pump Kit
DRU,PV411A (4771)
AU/MY
Provides up to 700Bar hydraulic, 40Bar pneumatic
pressures and vacuum to -950 mBar. Built-in stroke
adjuster, lower pressure fine control and tamper proof
overpressure protection.
Druck UPS III-IS Intrinsically Safe Loop Calibrator
DRU,UPS III-IS (4777)
AU
Measure or source 0 to 24mA and provide 24V loop power.
50 VDC measurement and continuity. Accuracy 0.015% of
reading, Hart compatible. Dual mA and % readout, linear
or flow. It is an essential tool for loop testing, instrument
maintenance and valve set-up, with an easy-to-read
display and simple-to-use time saving features.
Emerson Process Management 375
Field Communicator
EME,375 (4781)
AU/MY
Will configure, test, and diagnose your
HART® and Foundation FieldBus devices.
Able to communicate with any device, by
any manufacturer. Intrinsically safe. Easy
upgrade over the Internet. Interfaces with
AMS PC Suite Software.
Emerson 475 Hart Communicator
EME,475 (4779)
AU/MY
Will configure, test, and diagnose your HART® and
Foundation FieldBus devices. Able to communicate with
any device, by any manufacturer. Intrinsically safe. Easy
upgrade over the Internet. Interfaces with AMS PC Suite
Software.
Softing BC-600-PB Profibus Tester 4
SOF,PROFIBUS-4 (4775)
AU
Allows full testing of live PROFIBUS segments with
minimum influence on their operation. Detects transient
faults that occur sporadically. Test for non operation PLCs
or suspicious devices. Simultaneous analysis of both bus
physics and bus communication. Master simulator and
Topology scan. Expert tests: frame, oscillogram analysis
and trigger input/output. Long term trend measuring,
preventive maintenance and detailed test reporting.
Fitting Set with 700Bar Hose
FIT,HP
MY
Fitting set (max pressure = 10,000psi) for pressure calibrators. Female
connector sizes: 1/4 inch BSP & NPT; 1/8 inch BSP & NPT; 3/8 inch BSP &
NPT; 1/2 inch BSP & NPT.
Fitting Set With 20Bar Hose
FIT,LP
MY
Fitting set (max pressure = 10,000psi) for pressure calibrators. Female
connector sizes: 1/4 inch BSP & NPT; 1/8 inch BSP & NPT; 3/8 inc BSP &
NPT; 1/2 inch BSP & NPT.
Fluke 70Bar Pressure Transducer to suit Fluke
Calibrators 725 & 744
FLU,700P08-70BAR (4764)
AU
For use with the Fluke 744 & 725 industrial calibrators.
Pneumatic system range 0 to 70Bar, resolution
7mBar, reference uncertainty 0.025%. Connection 1/4
NPT and 1/4 ISO. Includes 700PTP-1 pressure pump.
(Note the pump will operate to 41Bar).
Fluke 690Bar Pressure Transducer to suit
Calibrators 744 & 725
FLU,700P31-690BAR (4765)
AU
For use with the Fluke 744 & 725 industrial calibrators.
Range 0 to 690Bar, reference uncertainty .025%.
Connection 1/4 NPT and 1/4 ISO Includes 700LTP-1
pressure pump.
Fluke 7Bar Pressure Transducer & Pump to suit FLU,744 & FLU,725
FLU,700PD6-7BAR (4763)
AU
For use with the Fluke 744 & &25 industrial calibrators. Range 100 to 690kPa,
reference uncertainty .025%. Connection 1/4 NPT and 1/4 ISO Includes
700LTP-1 pressure pump.
Fluke 718 300G Pressure Calibrator
FLU,718-300G (4793)
AU
Pressure source and milliamp measurement. Pressure
specs -83 to 2068kPa ±0.05% of range. Max pressure
2.6MPa. Current specs: 0.0001mA resolution,
accuracy 0.015%. Calibrate P/I (pressure to current)
transmitters, measures pressure via a 1/8 inch NPT
pressure fitting and an internal pressure sensor, source
pressure, measure current up to 24mA, simultaneously
display pressure and current measurements, supplies
loop voltage, calculates percentage in percent mode,
calculates mA error in percent error mode.
Fluke 719 2Bar-30G Pressure Calibrator including Electric Pump
FLU,719-30G (4795)
AU
2Bar, includes pump and precision 4 to 20mA measurement and source
capability. The pump in this instrument is electric. Uncertainty 0.025%.
Precision pressure adjustment vernier. Range -850mBar to 2Bar. Resolution
0.1mBar. 4 to 20mA resolution .001mA .015%rdg + 2 counts.
48