INSTRUCTIONS FOR INSTALLATION AND OPERATION elba

More documents

Recommendations

Info

Page 4 w w w. d r o o f f - k a m i n o f e n . d e INSTALL ATION Taking delivery of the stove Please check carefully that the stove is in perfect condition. Make sure that it has not been damaged in transit. Pay particular attention to the glass door and the fireclay bricks inside. Should you discover any damage, please inform your supplier at once. Do not light a fire in the stove. Damage sustained by the glass door and the fireclay bricks after the stove has been used is almost always caused by overheating or incorrect operation. In such cases, the manufacturer‘s guarantee will not apply and we will not be liable for any damage. CORRECT LOCATION n When choosing the location for your stove, make sure that it can be connected easily to the chimney in your house. Before installing the stove make sure you are aware of all the applicable national and local building regulations. n DROOFF stoves are normally delivered with an interchangeable connecting sleeve which makes it possible to fit the stovepipe both from the rear and from above (see data sheet "Technical Information"). As a rule, your stove will be prepared for connection from the top. However, if you prefer a different connection, replace the connecting sleeve with the sealing lid. It is extremely important that the opening which is not in use is firmly sealed with the lid. n The floor under the stove must be flat and level. Before installing the stove, make sure that the floor is able to bear the weight. n The floor under the stove must be resistant to heat and non-combustible (e.g. tiles or special floor plate). This non-combustible area must extend at least 50 cm in front of the stove and at least 30 cm to the side, measured from the front of the door. n The stove and the connecting pipe must be at a certain distance from combustible materials at the back and at the sides. They must also have a certain clearance from steelreinforced concrete walls. For the necessary safety clearances for your stove, please refer to the data sheet "Technical Information" or the plate attached to the back of the stove. For the necessary safety clearances for the connecting pipe, please refer to the data supplied by the pipe manufacturer. n Always ensure that no combustible objects or objects sensitive to heat are placed close to the glass door. See data sheet "Technical Information" for adequate clearances. DROOFF Kaminöfen — Feuer aus dem Sauerland
INSTALL ATION Seite 5 w w w. d r o o f f - k a m i n o f e n . d e CHIMNEY The stove functions by a simple principle of physics i.e. that hot gas rises. This means that the smoke and hot gas produced by the fire rise up through the chimney while fresh air for combustion is sucked into the fire chamber from the room or from outside (with stoves fitted with an outside air inlet). The upward draught from the chimney is therefore the "motor" of the stove. This draught is affected by a number of factors such as the cross section (wideness) of the chimney, its height and its insulation as well as the temperature outside the house. Every stove has its own characteristics. Deflection (i.e. changes in direction) of the smoke gas improve the efficiency of the stove but also creates resistance. The temperature and quantity of smoke gas produced differs from one stove type to another. Every stove therefore makes its own demands on the chimney. It may well happen that a good stove and a functioning chimney are incompatible and have to be adapted to one another. Always ask your stove dealer or a heating engineer if your chimney is suitable for your stove. n Connection to chimney The planned connection of a stove to a chimney must be approved according to national and local building regulations and carried out by a qualified engineer. The connection must also be officially tested before the stove is put into operation. DROOFF stoves are all designed according to type 1 with a self closing door to the fire chamber. They can be connected without difficulty to a suitable chimney which is already in use. The components required for connecting the stove to the chimney are not supplied with the stove. These components can be obtained from your dealer. For the correct diameter for the connecting sleeve of a DROOFF stove please refer to the attached data sheet "Technical Information". Smoke pipes complying with the standard EN 1856-2 are suitable for use with the stove. Always ensure that the smoke pipe is installed at the correct safe distance from combustible substances and materials. Wood burning stoves are technically complex devices. They function efficiently and safely only when installed and connected to a suitable chimney in accordance with all technical rules and regulations. You are therefore advised to have your stove installed and connected to the chimney by a qualified engineer. DROOFF Kaminöfen — Feuer aus dem Sauerland
Page 1 and 2: elba INSTRUCTIONS FOR INSTALLATION
Page 3: INSTRUCTIONS FOR INSTALL ATION AND
Page 7 and 8: INSTALL ATION Page 7 w w w. d r o o
Page 9 and 10: OPERATING INSTRUCTIONS Page 9 w w w
Page 11 and 12: OPERATING INSTRUCTIONS Page 11 w w
Page 17 and 18: DROOFF Kaminöfen — Feuer aus dem
Page 19 and 20: TECHNICAL INFORMATION Page 19 w w w

INSTRUCTIONS FOR INSTALLATION AND OPERATION elba

Create successful ePaper yourself

Delete template?

Save as template?