G1013 Manual - Grizzly Industrial Inc.

More documents

Recommendations

Info

Parts Inventory After all the parts have been removed from the carton, you should have: • Belt Guard • Disc Guard • Disc Table • Bolt Bag • Table Support • Sanding Unit • Motor • Miter Gauge • Belt Table • V-Belt • Base • Aluminum Disc • Disc Sanding Paper • Motor Pulley NOTICE A full parts list and breakdown drawing can be found toward the end of this manual. For easier assembly, or to identify missing parts, please refer to the detailed illustrations at the end of the manual. Hardware Qty 5 ⁄16" - 18 x 5 ⁄8" Carriage Bolts 5 5 ⁄16" - 18 x 3 ⁄4" Hex Bolts 4 5 ⁄16" - 18 Hex Nuts 13 5 ⁄16" Flat Washers 20 1 ⁄4" - 20 x 1 1 ⁄4" Hex Bolts 4 1 ⁄4" - 20 x 1" Hex Bolts 4 1 ⁄4" - 20 Nuts 4 1 ⁄4" Flat Washers 16 1 ⁄4" - 20 x 1 1 ⁄4" Carriage Bolts 2 1 ⁄4" - 20 Wing Nuts 2 M5-0.8 x 6mm Phillips ® Head Screws 4 5mm Flat Washers 4 1 ⁄4" - 20 x 3 ⁄8" Setscrews 2 3 ⁄16" Sq. x 3 ⁄4" Keys 2 5 ⁄16" Fender Washer 1 Rubber Feet 4 Wire Nuts 2 3mm Allen ® Wrench 1 -8- G1013 Combination Sander
Clean Up Site Consideration The unpainted surfaces are coated with a waxy oil to protect them from corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser. Avoid chlorine-based solvents as they may damage painted surfaces should they come in contact. Always follow the usage instructions on the product you choose for clean up. Do not use gasoline or other petroleum-based solvents to clean with. They have low flash points which make them extremely flammable. A risk of explosion and burning exists if these products are used. Serious personal injury may occur. Do not smoke while using solvents. A risk of explosion or fire exists and may result in serious personal injury. Many of the solvents commonly used to clean machinery can be toxic when inhaled or ingested. Always work in wellventilated areas far from potential ignition sources when dealing with solvents. Use care when disposing of waste rags and towels to be sure they do not create fire or environmental hazards. BENCH LOAD Your Model G1013 Combination Sander represents a relatively large weight load in a small footprint. Be sure that you workbench is adequately reinforced to support the weight of the sander. WORKING CLEARANCES Working clearances can be thought of as the distances between machines and obstacles that allow safe operation of every machine without limitation. Ensure that your working area offers plenty of room for free movement and a substantial amount of distance between you and others that may be working in your shop area. LIGHTING AND OUTLETS Lighting should be bright enough to eliminate shadow and prevent eye strain. Electrical circuits should be dedicated or large enough to handle combined motor amp loads. Outlets should be located near each machine so power or extension cords are not obstructing high-traffic areas. Be sure to observe local electrical codes for proper installation of new lighting, outlets, or circuits. Make your shop “child safe.” Ensure that your workplace is inaccessible to children by closing and locking all entrances when you are away. Never allow visitors in your shop when assembling, adjusting or operating equipment. G1013 Combination Sander -9-
Page 1 and 2: COMBINATION SANDER MODEL G1013 INST
Page 3 and 4: Table Of Contents PAGE 1. SAFETY SA
Page 5 and 6: Safety Instructions For Power Tools
Page 7 and 8: SECTION 2: CIRCUIT REQUIREMENTS 110
Page 9: Unpacking When you are completely s
Page 13 and 14: 3. Attach the Disc Table Support to
Page 15 and 16: 14. Align the table so that there i
Page 17 and 18: Belt Table Tilt Belt Replacement On
Page 19 and 20: SECTION 6: Operations Keep loose cl
Page 21 and 22: Inside Sanding Sharpening To sand o
Page 23 and 24: Maintenance Notes Date Approximate
Page 25: MACHINE DATA SHEET Customer Service
Page 28 and 29: WARRANTY AND RETURNS Grizzly Indust
Page 30: FOLD ALONG DOTTED LINE Place Stamp

G1013 Manual - Grizzly Industrial Inc.

Create successful ePaper yourself

Delete template?

Save as template?