Shanks Owners Manual (04 Build) 35, 35H & 40 (PDF) - EP Barrus

More documents

Recommendations

Info

Air Bleed Points Coolant from Engine Height Coolant to Engine Length Recommended Skin Tank Size Engine HP KW Skin tank Surface area m 2 Suggested Height mm Suggested Length mm 35 35 26 1.0 721 1442 40 40 30 1.125 750 1500 5. Pressurised Water Header Tank • The pressurised header tank should be mounted higher than the level of the engine and no more than 1 metre from the engine, to prevent cooling system air locks. 6. Shaft Connection • Some type of flexible coupling must be used to connect the gearbox output flange to the propeller shaft flange. 7. Engine Anti-Vibration Mounts • Ensure that the engine feet do not end up at the top of the thread on the engine mounts, this puts undue pressure on them and can result in excessive engine movement and premature mount failure. If this is a problem put steel packing plates under the mounts. Packing plates 25mm thick are available: order RDG3906 Engine mount spacer. Alternatively they can be manufactured locally. • Ensure that the engine has been installed for at least 24 hours before shaft alignment is checked, to allow the mounts time to settle under the engine weight. • Ensure that the anti-vibration mount centre screw is sufficiently raised so as not to touch the engine bed. If this occurs, excessive engine vibration will be experienced through the hull. RDG6038170 Shanks 04 Owners Manual Issue 4 Page 10 of 45
• For best results, fit the front anti-vibration mounts into the front holes in the engine rails. If engine room space is a problem the mounts can be fitted slightly further back in the alterative holes, and the front of the rail cut off – leaving 50mm of material to retain strength (measuring from the centre of the mount hole to the front end of the rail) 8. Engine Mount Installation • Care should taken to install mounts parallel to the engine rails with the washer and locknut firmly tightened on the cover of the mount. The maximum distance from the top of the locknut to the base of the adjusting nut must not exceed 5mm; any greater adjustment should be made using shims. RDG6038170 Shanks 04 Owners Manual Issue 4 Page 11 of 45
Page 1 and 2: SHANKS CANAL BOAT ENGINE MANUAL For
Page 3 and 4: 6. Secondary Fuel Filter Change ...
Page 5 and 6: PLEASE NOTE: This manual has been c
Page 7 and 8: 6. Batteries WARNING: EXPLOSIVE GAS
Page 9: SECTION 3 - Installation 1. Ventila
Page 13 and 14: 9. Engine Alignment • The gearbox
Page 15 and 16: Shanks 35 & 40 Engine filler tap cl
Page 17 and 18: SECTION 4 - Operation 1. Starting T
Page 19 and 20: engine range. It ensures that the e
Page 21 and 22: SECTION 5- Service Procedure 1. Eng
Page 23 and 24: good condition, tighten. Fit a new
Page 25 and 26: • Turn the main boat fuel supply
Page 27 and 28: 9. Belt Adjustment CAUTION: REMOVE
Page 29 and 30: d. The cap less bulb is a push fit
Page 31 and 32: Hydraulic gearbox filter Hydraulic
Page 33 and 34: 17. Oil Recovery Filter CAUTION: RE
Page 35 and 36: SECTION 7- Service Schedule Specifi
Page 37 and 38: SECTION 8 - Packing List Please ref
Page 39 and 40: Cylinder Head Tightening Pattern 9
Page 41 and 42: Panel Wiring Diagram RDG6038170 Sha
Page 43 and 44: Shanks04 35H RDG6038170 Shanks 04 O
Page 45: Shanks Instrument Panel Engine over

Shanks Owners Manual (04 Build) 35, 35H & 40 (PDF) - EP Barrus

Create successful ePaper yourself

Delete template?

Save as template?