- Page 1: Integrated Instruction Manual WP 60
- Page 5 and 6: Table of Contents GENERAL GUIDE....
- Page 7 and 8: 2.9 Calibration Report ............
- Page 9: GENERAL GUIDE This section is appli
- Page 12 and 13: 1.2 Inserting Batteries NOTE: Pleas
- Page 16 and 17: 2. System Setup Mode For All Meters
- Page 18 and 19: System setup sub-group allows you t
- Page 20 and 21: ON Time Back Light (permanently ON)
- Page 22 and 23: Protection Set Pass Word calibratio
- Page 24 and 25: 1. Press up & down arrow keys to en
- Page 26 and 27: It is recommended that you perform
- Page 29 and 30: 4. Measurement Mode For All Meters
- Page 31 and 32: 4.2.3 Stable reading indicator You
- Page 33 and 34: 5.2.1 Logging data automatically in
- Page 35 and 36: Transfer Stored data to CyberComm 5
- Page 37 and 38: 6. Technical Specifications Tempera
- Page 39 and 40: Resistivity Range Measuring ranges
- Page 41 and 42: 7. Accessories Eutech Instruments P
- Page 43 and 44: damage during shipment, and insured
- Page 46 and 47: 1. Temperature Setup Temperature se
- Page 48: 2.3 Temperature Calibration for MTC
- Page 52 and 53: 1. pH Setup pH setup sub-group allo
- Page 54 and 55: Buffer First Point of Calibration O
- Page 56 and 57: 2.4 pH Calibration with a User-defi
- Page 58 and 59: NEXT (F3) ESC (F4) ENTER Goes to pH
- Page 60: mV PARAMETER GUIDE 1. mV Setup Mode
- Page 63 and 64: 7. Press ESC (F4) to go to measurem
- Page 66:
ION PARAMETER GUIDE 1. Ion Setup Mo
- Page 69 and 70:
Use standard solutions of 0.001, 0.
- Page 71 and 72:
3. Ion Measurement Mode In Ion meas
- Page 74 and 75:
1. Conductivity Setup Conductivity
- Page 76 and 77:
2. Conductivity Calibration Mode 2.
- Page 78 and 79:
2.7 Manual Calibration Note: If you
- Page 80 and 81:
2.9 Calibration Report Calibration
- Page 82 and 83:
- END OF CONDUCTIVITY SECTION - 74
- Page 85 and 86:
1. TDS Setup The TDS setup screen p
- Page 87 and 88:
2. TDS Calibration Mode You can com
- Page 89 and 90:
3. TDS Measurement Mode In TDS meas
- Page 91:
SALINITY PARAMETER GUIDE 1.Salinity
- Page 94 and 95:
Salinity Settings Page 2 - Hi-Lo Se
- Page 96 and 97:
2.1 Salinity Calibration Report Cal
- Page 99:
RESISTIVITY PARAMETER GUIDE 1.Resis
- Page 102 and 103:
Resistivity Settings Page 2 - Hi-Lo
- Page 104 and 105:
Note: The function of the keys avai
- Page 107 and 108:
DISSOLVED OXYGEN PARAMETER GUIDE PA
- Page 109 and 110:
PART A - % Saturation Mode 1. O2 %
- Page 111 and 112:
disabled) 2. DO Calibration in % Sa
- Page 113 and 114:
Function Keys available in saturati
- Page 115 and 116:
2.4 % Saturation Offset Adjustment
- Page 117 and 118:
Figure 56 : DO (mg/L) - Page 1 This
- Page 119 and 120:
2. DO Calibration in mg/L mode or p
- Page 121 and 122:
Figure 60 : DO Calibration Report i
- Page 123 and 124:
This makes it possible to measure t
- Page 125 and 126:
7. Rinse the membrane cap and membr
- Page 127 and 128:
119