- Page 1: Integrated Instruction Manual WP 60
- Page 6 and 7: TEMPERATURE .......................
- Page 8 and 9: 2.2.1 Auto Salinity Compensation ..
- Page 11 and 12: 1. Overview For All Meters 1.1 Abou
- Page 13 and 14: 1.3 Attaching the Belt To attach th
- Page 15 and 16: 1.4.2 Protective Rubber Boot The ru
- Page 17 and 18: 1. Press ENTER key to select Setup
- Page 19 and 20: System Settings Page 2 - Date & Tim
- Page 21 and 22: TEXT - Select this format if you us
- Page 23 and 24: This allows you to clear the memory
- Page 25 and 26: 3. Calibration Mode For All Meters
- Page 27: All new calibration values will aut
- Page 30 and 31: MODE (F3) OFF (F4) ENTER Switches b
- Page 32 and 33: 4.4 Alarm set point (For pH/conduct
- Page 34 and 35: 5.2.4 Transferring stored data to t
- Page 36 and 37: 5.2.6 Transferring stored data to a
- Page 38 and 39: Conductivity Range Measuring ranges
- Page 40 and 41: Set Point Alarm Input DO Display Ye
- Page 42 and 43: 2-cell Electrode with ATC, cell con
- Page 44: TEMPERATURE PARAMETER GUIDE i. Temp
- Page 47 and 48: eplacement probe. This procedure of
- Page 50: pH PARAMETER GUIDE 1. pH Setup Mode
- Page 53 and 54:
pH Settings Page 2 - Calibration Du
- Page 55 and 56:
(a) (b) Figure 17: pH Calibration S
- Page 57 and 58:
ESC (F4) ENTER Exits from calibrati
- Page 59 and 60:
3.2 Indicators in pH measurement sc
- Page 62 and 63:
1. mV Setup Mode There is no setup
- Page 64:
Item Description 1 Measurement mode
- Page 68 and 69:
1. Ion Setup Ion setup sub-group al
- Page 70 and 71:
7. The upper display shows the next
- Page 72:
CONDUCTIVITY PARAMETER GUIDE 1. CON
- Page 75 and 76:
Note: 1. If pure water coefficient
- Page 77 and 78:
2.5 Pure Water Coefficient Pure wat
- Page 79 and 80:
Figure 32 : Conductivity Calibratio
- Page 81 and 82:
2 1 3 4 5 6 7 8 10 11 9 11 12 Figur
- Page 83:
TDS PARAMETER GUIDE 1.TDS Setup Mod
- Page 86 and 87:
TDS Settings Page 2 - Hi-Lo Set Poi
- Page 88 and 89:
Note: The function of the keys avai
- Page 90 and 91:
4. About TDS 4.1 Calculating TDS Co
- Page 93 and 94:
1. Salinity Setup Salinity setup sc
- Page 95 and 96:
3. The meter shows the ‘Calibrati
- Page 97:
3. Salinity Measurement Mode In Sal
- Page 101 and 102:
1. Resistivity Setup The resistivit
- Page 103 and 104:
2. Resistivity Calibration Mode Use
- Page 105:
3. Resistivity Measurement Mode In
- Page 108 and 109:
100
- Page 110 and 111:
NOTE: During measurement, the meter
- Page 112 and 113:
Figure 51: Saturation Calibration S
- Page 114 and 115:
2.3.1 % DO Calibration Report Calib
- Page 116 and 117:
6 7 8 9 10 11 Figure 55 : Percentag
- Page 118 and 119:
Figure 57: DO (mg/L) - Page 2 This
- Page 120 and 121:
which the meter is going to be cali
- Page 122 and 123:
Figure 61 :Concentration Measuremen
- Page 124 and 125:
Your new DO probe comes with replac
- Page 126 and 127:
NOTES 118
- Page 128:
Note:The the TDS factory conversio