00 Contents - Hilti Svenska AB

More documents

Recommendations

Info

Introduction 1.3 Direct fastening applications Typical applications for powder or gas-actuated fastening are shown in the illustrations below: • Fastening thin metal sheets: Roof decking wall liners and floor decking • Fastening thicker steel members: e.g. metal brackets, clips • Fastening soft materials such as wooden battens or insulation to steel, concrete or masonry • Threaded studs for suspended ceilings, installing building services, bar gratings or checker plate floors • Connections for composite structures: Fastening nailed composite shear connectors Roof decking Wall liners Floor decking Metal brackets, clips and tracks Fixtures for mechanical and electrical installations Wooden battens fastened to steel or concrete HILTI Hangers with threaded connectors Grating fastenings Shear connectors 1.6 11 / 2007
Hilti direct fastening systems are specially designed for each application and trade. Introduction Key applications and the corresponding fastening systems are shown below. Roof and floor decking in steel & metal construction X-ENP-19 L15 DX 76 PTR Gratings in the petrochemical and other industries X-BT + X-FCM R DX 351 BTG Interior partition walls (drywall) in interior finishing X-GN GX 120 11 / 2007 1.7
Page 1 and 2: Principles and technique Introducti
Page 3 and 4: Introduction Introduction 1 1.1 Def
Page 5: ? + ? + = 2.4 kN + + = 2.4 kN A com
Page 9 and 10: The direct fastening system Introdu
Page 11 and 12: 2.1 Fasteners The direct fastening
Page 13 and 14: Stainless steel fasteners Hilti int
Page 15 and 16: Hilti Tools All Hilti tools supplie
Page 17 and 18: The direct fastening system DIN 726
Page 19 and 20: Health and safety Introduction 1 Th
Page 21 and 22: Drop-firing safety The drop firing
Page 23 and 24: ystanders. Safety tests with carton
Page 25 and 26: Quality of installation The use of
Page 27 and 28: Corrosion Introduction 1 The direct
Page 29 and 30: 2. Contact corrosion Corrosion is a
Page 31 and 32: Hilti X-CR / X-BT stainless steel f
Page 33 and 34: Steel base material Introduction 1
Page 35 and 36: Fusing (welding) Complete fusing of
Page 37 and 38: Guide values for the depth of penet
Page 39 and 40: Steel base material Surface of the
Page 41 and 42: Steel base material Compressive str
Page 43 and 44: 5.5 Thin steel base material Steel
Page 45 and 46: Failure of the base steel If the th
Page 47 and 48: Pull-over test specimen at test beg
Page 49 and 50: X-CRM8-15-12 (stainless steel faste
Page 51 and 52: Steel base material 5.7 Effect of f
Page 53 and 54: 5.9 Effect on the fatigue strength
Page 55 and 56: Concrete base material Introduction
Page 57 and 58:
Clamping The compressibility of con
Page 59 and 60:
Concrete parameter The concrete par
Page 61 and 62:
Edge distance and fastener spacing
Page 63 and 64:
Masonry base material Introduction
Page 65 and 66:
Temperature effects Introduction 1
Page 67 and 68:
Base steel: S355K2G3 h = 25 mm fy =
Page 69 and 70:
8.3 Fire rating of fastenings to st
Page 71 and 72:
Temperature effects 8.4 Fire rating
Page 73 and 74:
Design concepts Introduction 1 The
Page 75 and 76:
The characteristic strength is defi
Page 77 and 78:
Determination of technical data Int
Page 79 and 80:
10.2 Profile sheet fastenings Deter
Page 81 and 82:
Calculation method The calculation
Page 83 and 84:
Determination of technical data The
Page 85 and 86:
DX fastenings on concrete Fault Fas
Page 87 and 88:
DX fastenings on steel Fault Nail d
Page 89 and 90:
Approval Listing Summary of approva
show all

00 Contents - Hilti Svenska AB

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?