8 FROnT-PAnEL COnTROLS power Indicator: This LED has three possible modes: • Main Power Off: When the <strong>AVR</strong> is unplugged or the rearpanel Main Power Switch is off, this LED is off. • Standby: Amber indicates that the <strong>AVR</strong> is ready to be turned on. • On: When the <strong>AVR</strong> is turned on, this LED turns white. note: If the PROTECT message ever appears, turn off the <strong>AVR</strong> and unplug it. Check all speaker wires for a possible short. If none is found, bring the unit to an authorized <strong>Harman</strong> <strong>Kardon</strong> service center for inspection and repair before using it again. Standby/on Switch: This electrical switch turns the receiver on, or places it in Standby mode for quick turn-on. tuning mode: This button toggles between manual (one frequency step at a time) and automatic (seeks frequencies with acceptable signal strength) tuning mode. It also toggles between stereo and mono modes when an FM station is tuned. channel Level control: Press this button to adjust the output level for any amplifier channel. It may be necessary to raise or lower the level of a specific channel to compensate for the placement of the relevant speaker in the room in relation to the listening position; e.g., the center channel speaker is further away from the listening position than the front left and right speakers, so that the dialogue is too soft to hear clearly. To adjust the level of a channel, press this button once. If the desired channel is not displayed on screen and in the front-panel Message Display, use the Tuning Buttons to scroll to it. When the desired channel appears, use the Navigation Buttons to change the level. It is recommended that you avoid changing the channel levels after you have run the EzSet/EQ setup procedure described in the Initial Setup section, which properly adjusts all channel levels. See the Advanced Functions section for more information on manual speaker setup, including level adjustment. remote Ir Sensor: This sensor receives infrared (IR) commands from the remote control. It is important to ensure that it is not blocked. If covering the sensor is unavoidable, use an optional <strong>Harman</strong> <strong>Kardon</strong> HE 1000, or other infrared receiver, connecting it to the Remote IR Input on the <strong>AVR</strong> <strong>1600</strong>’s rear panel. Digital Input: To change the audio input for the current source to one of the six digital audio inputs or the analog input for the source, press this button and use the Navigation Buttons to change the input. Although any digital audio input may be assigned to any source, the analog audio inputs are all permanently dedicated to the source with which they are labeled. navigation: These buttons are used to navigate the <strong>AVR</strong>’s menus. Set: Press this button to select the currently highlighted item. message Display: Various messages appear in this two-line display in response to commands and changes in the incoming signal. In normal operation, the current source name appears on the upper line, while the surround mode is displayed on the lower line. When the on-screen display menu system (OSD) is in use, the current menu settings appear. tuning: Press these buttons to tune a radio station. Surround mode: Press this button to select a surround sound (e.g., multichannel) mode. Each press changes the surround mode category: AUTO SELECT, VIRTUAL, STEREO, MOVIE, MUSIC, VIDEO GAME. To change the specific mode within the category, use the Surround Select Buttons. See the Advanced Functions section for more information on surround modes. Surround Select: After you have selected the desired surround mode category, press these buttons to select a specific mode within the category, such as to change from Dolby Pro Logic IIx Movie mode to Logic 7 Movie mode. Surround mode availability depends on the nature of the source input signal, i.e., digital versus analog, and the number of channels encoded within the signal. Source Selectors: Press these buttons to select a source device, which is a component where a playback signal originates, e.g., DVD. Headphone Jack/ezSet/eQ microphone Input: Plug a 1/4” headphone plug into this jack for private listening. This jack is also used to connect the supplied microphone for the EzSet/EQ procedure described in the Initial Setup section. Digital audio Inputs (optical 3 and coaxial 3): Connect a source component that will only be used temporarily, such as a digital camera or game console, to these jacks. Use only one type of audio. The audio input may be assigned to any video source. uSB port: This port may be used in case a software upgrade for the receiver is offered in the future. Do not connect a storage device, peripheral product or a PC here, unless instructed to do so as part of an upgrade procedure. Video 3 analog audio and Video Inputs: Connect a source component that will only be used temporarily, such as a digital camera or game console, to these jacks. These inputs are selected as the Video 3 source, and may not be assigned to other sources. Volume knob: Turn this knob to raise or lower the volume.
DVD Audio/Video Inputs AC Power Cord Component 1 & 2 Inputs HDMI 1-3 Inputs HDMI Monitor Output Video 2 Audio/Video Inputs Video 1 Audio/Video Inputs & Outputs Video Monitor Output Component Video Monitor Output REAR-PAnEL COnnECTiOnS FM Antenna 6-/8-Channel Analog Audio Inputs Coaxial 1 & 2 Digital Audio Inputs CD Inputs AM Antenna AUX Input Optical 1& 2 Digital Audio Inputs Main Power Switch Coaxial Digital Audio Output Center Speaker Outputs Subwoofer Output Surround Speaker Outputs Surround Back Speaker Outputs Front Speaker Outputs Tape Audio Inputs & Outputs note: To make it easier to follow the instructions throughout the manual that refer to this illustration, a copy of this page may be downloaded from the Product Support section at www.harmankardon.com. 9
Change language