owner's manual - Hydropool

More documents

Recommendations

Info

LED Light Assembly The light wire harnesses are bundled & attached to the control box on the equipment platform. One light is located on the riser of the middle step and the other is located under the swim jets. You will need to attach the light at the swim jet end only. Clip the plastic LED light assembly onto the clear housing. Note: Aquaplay model has one light at the step end Topside Control Panel connection Connect the topside control panel extension cable (located on equipment platform) to main topside control cable located under the control panel. IMPORTANT ELECTRICAL SAFETY INSTRUCTIONS Safety comes first. When installing & using this electrical equipment, basic safety precautions Must always be followed! 1 READ AND FOLLOW ALL INSTRUCTIONS 2 Electrical installation must be completed by a qualified electrician in accordance with all National, Regional and Local Codes and Regulations in effect at the time of installation. 3 Connect only to a dedicated circuit protected by a class ‘A’ two-pole ground fault circuit interrupter (GFCI) 4 Use copper conductors only! 5 The Swim spa equipment and all electrical plugs, outlets and lights within 1.5m (5ft) of the unit must be G.F.C.I protected. Consult your electrician or local electrical authority for further details. 6 A green colored terminal or a terminal marked “G”, “GR”, “Ground”, or “Grounding” is located inside the supply terminal box or compartment. To reduce the risk of electric shock, this terminal must be connected to the grounding means provided in the electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors supplying the equipment. 7 At least two lugs marked “BONDING LUGS” are provided on the external surface or on the inside of the supply terminal box or compartment. To reduce the risk of electric shock, connect the local common bonding grid in the area of the swim spa to these terminals with an insulated or bare copper conductor not smaller than No.6 AWG (Canada/Europe) / No.8 AWG (USA). 8 All field installed metal components such as rails, ladders, drains or other similar hardware within 3 m (10 ft) of the swim spa shall be bonded to the equipment grounding bus with copper conductors not smaller than No.6 AWG. The steel support legs must be grounded. 14 Wire Size North America • The minimum wire size for systems that require a 40A GFCI is #8/3 c/w ground (also refered to as #8 gauge/4 conductor). • The minimum wire size for systems that require a 50A or 60A GFCI is #6/3 c/w ground (also refered to as #6 gauge/4 conductor). Europe • The minimum wire size for European system is 2.5 mm 2 copper wire. G.F.C.I./R.C.D. Application Guide North America Aquatrainer Aquaplay Europe All models (single-phase) 60A 40A 40A Important Note: • This guide is for standard installations where the wire run is 15 m (50 ft.) or less. For longer wire runs, consult a qualified electrician.
North America – GFCI INSTALLATION Important Note: Installation of the GFCI - Circuit Breaker, including ampere sizing and selection of conductor size and type, must be performed by a qualified electrician in accordance with the National Electrical Code, or the Canadian Electrical Code, and all Federal, State/Provincial and local codes and regulations in effect at the time of installation. SIEMENS - TYPICAL TEST 60 60 O N O F F N OTE THIS - The white Neutral wire from the back of the GFCI M UST be connected to an incoming Line Neutral. The internal mechanism of the GFCI requires this neutral connection. The GFCI will not work without it. White Wire Line Neutral LOAD POWER LOAD NEUTRAL LOAD POWER LINE NEUTRAL - LINE 2 - INPUT LINE 1 - INPUT GROUND GROUND - INPUT From Electric Service Panel or Other Source Note: Ground bar (included) must be installed in p anel. GROUND TO SPA LOAD 2 - LOAD NEUTRAL - LOAD 1 - 120 volts 120 volts 240 volts To swim spa support equipment square d - TYPICAL front view of G.f.c.I. (square D) bottom view of G.f.c.I. (square D) RED (HOT) GRN WHITE RED (HOT) BLACK (HOT) GRN (GROuND) WHITE (NEuTRAL) RED (HOT) BLACK (HOT) BLACK (HOT) RED (HOT) WHITE WHITE GRN (GROuND) GRN (GROuND) BLK (HOT) WHITE WHITE 1 WHITE (NEuTRAL) 2 BLACK (HOT) 3 RED (HOT) 4 GREEN (GROuND) 5 tbI 15
Page 1 and 2: Hydropool Industries: Tel: 905.565.
Page 3 and 4: Since manufacturing our first swim
Page 5 and 6: CHOOSING THE RIGHT LOCATION Your Hy
Page 7 and 8: Site preparation Above-ground Insta
Page 9 and 10: REMOTE Equipment REMOTE EQUIPMENT p
Page 11 and 12: LEVELING YOUR HYDROPOOL Swim Spa Af
Page 13: Support Equipment Assembly Position
Page 17 and 18: Swim Jets pump(S) timer - Europe on
Page 19 and 20: LED Mood lIGHTing Press the ‘ligh
Page 21 and 22: Unions Blue Drain Hose Gate Valves
Page 23 and 24: To Check/Change the set temperature
Page 25 and 26: Topside Panel Lock Features TEMPERA
Page 27 and 28: PUMP / JETS FUNCTION Press this pad
Page 29 and 30: Hydropool Swim spa Series Control S
Page 31 and 32: SETTING SECOND ECONOMY CYCLE START
Page 33 and 34: Hydropool Swim Spa Series Control S
Page 35 and 36: PROGRAMMING Filter Cycles To change
Page 37 and 38: Hydropool Swim Spa Series Control S
Page 39 and 40: Topside Panel Display Messages / /
Page 41 and 42: JET and FEATURE OPERATION Poly Stor
Page 43 and 44: OVERVIEW OF CONTROLS HYDROPOOL SURR
Page 45 and 46: AM/FM CD PLAYER CONTROLS SETTING ST
Page 47 and 48: GLOSSARY OF COMMON WATER MAINTENANC
Page 49 and 50: Corona Discharge Ozone Technology A
Page 51 and 52: CHANGING THE SWIM SPA WATER The wat
Page 53 and 54: WINTERIZING YOUR HYDROPOOL swim spa
Page 55: GENERAL TROUBLESHOOTING Continued W

owner's manual - Hydropool

Create successful ePaper yourself

Delete template?

Save as template?