Sage 1a Controller - Categories On Thermal Solutions Products LLC ...

More documents

Recommendations

Info

Installation Communication (Continued) The TSBC communication selections are found on the Communication Menu. Press and hold the key to leave the Display Mode and access the Main Menu: MENU Use the keys scroll down to the Communication Menu and push the ENTER key: Communication Menu No. Range / Choices Parameter and Description 90 Peer to Peer Modbus 91 1-247 92 93 94 95 96 9.6 19.2 38.4 Odd Even None 1-120 Seconds 97 1 to 8 98 - - 6 - - - 321 Protocol Selects between Peer-To-Peer (multiple boiler Lead/Lag control network) and a Modbus slave communication. Modbus Address Each boiler must be given a unique address. Only visible when Protocol equals Modbus. Baud Rate Units are 1000 Bits Per Second (KBPS). Only visible when Protocol equals Modbus. Parity Only visible when Protocol equals Modbus. Timeout Only visible when Protocol equals Modbus. Messages Rcvd Diagnostic tool used to confirm wiring and Modbus master configuration. Only visible when Protocol equals Modbus. Messages Sent Diagnostic tool used to confirm wiring and Modbus master configuration. Only visible when Protocol equals Modbus. Boiler Address Each boiler must be given a unique address. The boiler address assignment determines the boiler sequencing order. A value of 0 disables the network communications. Only visible when Protocol equals Peer to Peer. Online Status Each space can be either the boiler address or a ‘ - ‘ depending on whether there is a boiler of that address on-line. Only visible when Protocol equals Peer to Peer. Example: - - 6 - - - 321 indicates that boilers 6,3,2 and 1 are online TSBC Instruction Manual Page 24 of 48
Installation Peer-To-Peer Network The TSBC includes a dependable Peer-To-Peer communication network. This network allows multiple boiler modulating lead/lag control and status signals to be transferred between boilers. In order to successful use this network certain requirements must be followed. Network Relevant & Updated Parameters When using the Peer-To-Peer network certain “Network Relevant” parameters must be configured the same in all boilers (refer to Appendix B for parameter identification). To facilitate the configuration of these “Network Relevant” parameters, a network update feature has been included. Once communications is established between all boilers in a system, changing to a “Network Relevant” parameter at the keypad of any boiler will update that parameter in all boilers. In addition to the “Network Relevant” parameters, other common parameters are also “Updated” over the network (although it is not necessary for them to be set identically among boilers on the network). If you wish to configure them differently among boilers, you will have to disconnect the boiler from the network while you change them to prevent the other boiler from being changed as well. “Network Relevant” and additional “Updated” parameters are identified in Appendix B, Parameter Summary. Initially Establishing Peer-to-Peer Communication A Peer-to-Peer network is established as follows: 1. Assign all boilers a unique Boiler Address between 1 and 8 and set the Protocol to Peer-to-Peer. 2. Connect all boilers using a RJ11 ended telephone cable. 3. Configure all “Network Relevant” parameters identically on all boilers. Unexpected boiler behavior may result if these parameter values differ among boilers on the network. When “Network Relevant” parameters are identical the ‘Param Code’ parameter will be identical on each boiler (refer to page 40 for parameter location). 4. When two or more boilers are properly configured for communication, the controllers “auto detect” each other and shares information. Re-Establishing Peer-to-Peer Communication After an Individual Boiler Communication Failure A Peer-to-Peer network is re-established as follows: 1. Ensure Boiler address is between 1 and 8 and is unique. 2. Ensure the Protocol parameter is set to Peer-to-Peer. 3. Use the ‘Param Code’ parameter to check that “Network Relevant” parameters are configured identically (refer to page 40 for parameter location). 4. Remove control power from the boiler. 5. Connect the boiler to the network using a RJ11 ended telephone cable. 6. Apply control power to the boiler. 7. The network will “auto detect” the new boiler and assign it a position in the sequence based on the boiler address. When a boiler is operated as a stand alone boiler, away from the network, it establishes itself as a lead boiler. If this stand alone boiler is simply re-connecting to a network of operating boilers there is a potential that boiler operation will be disrupted as the new boiler becomes lead. This potential is avoided by following the above Re-Establishing procedure. TSBC Instruction Manual Page 25 of 48
Page 1 and 2: Contents Thermal Solutions Boiler C
Page 3 and 4: Introduction Quick Reference Abbrev
Page 5 and 6: Introduction Overview Fresh Air Sup
Page 7 and 8: Product Features Boiler Sequence (C
Page 9 and 10: Product Features Single Boiler Cont
Page 11 and 12: Product Features Energy Management
Page 13 and 14: Product Features Energy Management
Page 15 and 16: Product Features Auxiliary Device C
Page 17 and 18: Front Panel Display Mode All values
Page 19 and 20: Front Panel Setpoint Menu Deg F Wat
Page 21 and 22: Installation External Connections S
Page 23: Installation Communication The Peer
Page 27 and 28: Installation RS485 Modbus Network M
Page 29 and 30: Configuration & Tuning System Confi
Page 31 and 32: Configuration & Tuning Setup Menu (
Page 33 and 34: Configuration & Tuning Setup Menu (
Page 35 and 36: Configuration & Tuning Manual Mode
Page 37 and 38: Trouble Shooting Alarm Messages (co
Page 39 and 40: Trouble Shooting Diagnostic Menu (C
Page 41 and 42: Trouble Shooting Sensor Temperature
Page 43 and 44: Specifications General Mechanical:
Page 45 and 46: Appendix A Parameter Summary Networ
Page 47 and 48: Appendix B Supervisor Parameter Wor

Sage 1a Controller - Categories On Thermal Solutions Products LLC ...

Create successful ePaper yourself

Delete template?

Save as template?