1.0 - SATA-IO

More documents

Recommendations

Info

The measurement units can be altered from pico seconds to UI by right click on “Total Jitter” on the left side bar; then click on “Configure”, select “Percentage Unit Interval”, click “OK”. 9. Repeat 4 through 6 with the LBP pattern loaded in the detector and the PUT initiated transmitting the LBP pattern. 10. Optionally repeat 4 through 6 with the PUT initiated transmitting the SSOP pattern. Observable Results: The pass/fail criteria are: • TSG-09a and b: TJ measured must be less than 0.37 UI at 1.5 Gb/s for each of the test patterns. • TSG-10a and b: DJ measured must be less than 0.19 UI at 1.5 Gb/s for each of the test patterns. Serial ATA Logo Group 24 MOI Revision 1.3 Version 1.0 using BERTScope
Test Title: TSG-11: TJ at Connector, Clock, 500 Test Title: TSG-12: DJ at Connector, Clock, 500 Purpose: Verify that the Product Under Test, PUT, meets the TJ specification of section 7.2.2.3.12 and 7.3 of Serial ATA revision 2.6 while transmitting various specified patterns, namely HFTP (D10.2), LBP and optionally if test time permits SSOP at 3 Gb/s. Last Modification: January 5, 2009 Discussion: This test requirement is only applicable to components claiming to be capable of running at 3Gb/s. The BERTScope simultaneously measures the TJ and DJ for TSG-11 and TSG-12 using the BERT method according to sections 7.4.6 and 7.4.8 of the Serial ATA revision 2.6. Resource Requirements and Test Setup as shown in Appendix E. Test Procedure: 1. On CR 12500A, choose the pre-stored selection: “JTF-SATA2”; by pressing “Enter”, scroll to the desired setting and press “Enter” again. On the CR 12500A also set the sub-rate clock divider to 1 by scrolling to “SubDiv: 4” press “Enter” select “1” and press “Enter” again. 2. On the BERTScope, select “View” then “Detector”. Click on “Error Detector”, deselect “Auto Pattern”. Click on “Error Detector” again, select “Pattern” and click on “User Pattern”. 3. Click on “Error Detector” a third time, select “User Pattern Mode” and click on “Shift”. Click a fourth time on “Error Detector”, select “Load User Pattern” and select the HFTP pattern. Serial ATA Logo Group 25 MOI Revision 1.3 Version 1.0 using BERTScope
Page 1 and 2: SyntheSys Research, Inc. Serial ATA
Page 3 and 4: MODIFICATION RECORD First draft, Ja
Page 5 and 6: Test Title: Host Worst Port Identif
Page 7 and 8: Observable Results: • The observa
Page 9 and 10: • PHY-01a: Mean Unit Interval mea
Page 11 and 12: 6. Record Max. Deviation (in ppm) a
Page 13 and 14: 4. Click on “Run” on the right
Page 15 and 16: Test Title: TSG-03: Differential Sk
Page 17 and 18: Test Title: TSG-04: AC Common Mode
Page 19 and 20: Test Title: TSG-05: Rise/Fall Time
Page 21 and 22: 6. Move the cable from the CR 12500
Page 23: 4. Initiate the PUT transmitting th
Page 27 and 28: The measurement units can be altere
Page 29 and 30: 6. Repeat step 6 above with the Dat
Page 31 and 32: 8. Use the “Bit Cursors” from
Page 33 and 34: Test Title: OOB-06: COMWAKE Gap Det
Page 35 and 36: Appendix A: Initiation of PUT using
Page 37 and 38: Appendix B1: Calibration of Test Se
Page 39 and 40: Calibration Procedure: 1. Set the d
Page 41 and 42: Observable Results: The calibration
Page 43 and 44: Serial ATA Logo Group 43 MOI Revisi
Page 45 and 46: connector to the 50 ohm load within
Page 47: Last Modification: January 5, 2009

1.0 - SATA-IO

Create successful ePaper yourself

Delete template?

Save as template?