DFX, DBX Vent-Free Fireplace Systems - Unvented Gas Log Heater ...

More documents

Recommendations

Info

DFX & DBX Series Vent Free Fireplaces FINAL INSTALLATION WARNING Do not operate the unit without the screen frame panel and canopy installed. Canopy REMOVE SCREEN Figure 16 1. Remove bottom louver. 2. Removing fireplace screen frame panel by pushing screen frame panel up and out. NOTE: Fireplace screen must be removed to access log box and to install canopy. Fireplace Screen Louvre Figure 16 - Remove Fireplace Screen Panel FP2513 INSTALL CANOPY Figure 17 1. Push louvers up and out to remove top louver assembly. 2. Align the black canopy with the holes in the top frame assembly. 3. Install the three (3) screws (in owner’s manual packaging) which attach the canopy to the top frame assembly. 4. Tighten all screws. Make sure the canopy is level and secure. Install top louver assembly. Figure 17 - Install Canopy FP2513 Screws remove screen Canopy FP2514 FP2514 install canopy 16 33D4047
LOG PLACEMENT DFX & DBX Series Vent Free Fireplaces Before you begin — This unit is supplied with six (6) ceramic fiber logs. Do not handle these logs with your bare hands. Always wear gloves to prevent skin irritation from ceramic fibers. After handling the logs, wash your hands gently with soap and water to remove any traces of fibers. WARNING CAUTION The positioning of the logs is critical to the safe and clean operation of this heater. Sooting and other problems may result if the logs are not properly and firmly positioned in the appliance. Never add additional logs or embellishments such as pine cones, vermiculite or rock wool to the heater. Only use the logs and TPB-RW (rock wool) supplied with the unit. Failure to position the parts in accordance with diagrams below or to use only parts specifically approved for this heater may result in property damage or personal injury. DO NOT sprinkle volcanic rock on the logs or around the pilot or the main burner. This may cause sooting. Only place volcanic rock on the floor of the fireplace. During initial operation of the new heater, burning logs will give off a paper burning smell and orange flames will be present. Simply open the windows for a few hours to vent the odor. DFX24C log placement Figure 18 1. Install the rear log (#3) on back of burner. 2. Install the right log (#1) on burner pins on right side of burner. 3. Install the left log (#2) on burner pins on left side of burner. Left Log #2 Right Log #1 Rear Log #3 Burner Pins Burner Pins Figure 18 - DFX24C Log Placement LG699 33D4047 17 LG699 24VFSC logs
Page 1 and 2: DFX, DBX Vent-Free Fireplace System
Page 3 and 4: IMPORTANT SAFETY INFORMATION INSTAL
Page 5 and 6: PRODUCT FEATURES DFX & DBX Series V
Page 7 and 8: Preinstallation information WARNING
Page 9 and 10: FIREPLACE INSTALLATION DFX & DBX Se
Page 15: ELECTRICAL INSTALLATION DFX & DBX S
Page 19 and 20: FLAME APPEARANCE DFX & DBX Series V
Page 21 and 22: OPERATING INSTRUCTIONS DFX & DBX Se
Page 23 and 24: OPERATING INSTRUCTIONS DFX & DBX Se
Page 25 and 26: TROUBLESHOOTING DFX & DBX Series Ve
Page 27 and 28: REPLACEMENT PARTS DFX & DBX Series
Page 29 and 30: REPLACEMENT PARTS DFX & DBX Series
Page 31 and 32: OPTIONAL ACCESSORIES install option
Page 33 and 34: OPTIONAL ACCESSORIES DFX & DBX Seri
Page 35 and 36: Lifetime Warranty DFX & DBX Series

DFX, DBX Vent-Free Fireplace Systems - Unvented Gas Log Heater ...

Create successful ePaper yourself

Delete template?

Save as template?