HOT WATER OUR ELEMENT - Stiebel Eltron

FREESTANDING DHW CYLINDERS
Model Freestanding DHW cylinder Inst. water heating cylinder Inst. water heating cylinder
– Type HSTP 200 HSTP 300 HSTP 400 SBS 800 W SBS 1000 W SBS 1500 W SBS 800 W SOL SBS 1000 W SOL SBS 1500 W SOL
– Part no. 071264 071267 071270 227568 227569 227570 227571 227572 227573
Application
– Nominal capacity l 200 300 400 800 1,000 1,500 800 1,000 1,500
Connection details
– Mode of operation
– Dual/single circuit cylinder 1) • • •
Key
• Available, or yes.
1) Dual-circuit system for reheating during the day, subject to demand.
2) Permissible heating side 0.3/3 MPa/bar.
3) The mixed water volume has a service temperature of 40 °C which is
based on a cold water temperature of 15 °C and a cylinder water
temperature of 65 °C (with respect to the operational state).
Combined DHW and
heating water buffer cylinder
Combined DHW and
heating water buffer cylinder
– Water connection
(external thread) below/above G1" / G1" G1 ¼" G1 ¼"
– DHW circulation connection G ½" – – – – – –
– Heat pump connection – G1 ½" G1 ½" G2" G1 ½" G1 ½" G2"
– Heating circuit connection – G1 ½" G1 ½"
– Connection for opt. heat source – G1 ½" G1 ½"
– Permiss. op. pressure MPa/bar 0.6 / 6 0.6 / 6 2) 0.6 / 6 2)
– Mixed water volume of 40 °C 3) l 397 590 792 – – – – – –
– Stand-by power consumption
at 65 °C / 24 h kWh 1.9 2.2 2.7 – – – – – –
– Connected load and
voltage 4)
Dual-circuit operation: 2/4 kW, 4/4 kW
1/N/PE ~ 230 V; 2/6 kW, 3/6 kW, 4/6 kW,
6/6 kW | 3/N/PE ~ 400 V
Single circuit operation: 2 kW, 4 kW
1/N/PE ~ 230 V; 2 kW, 3 kW, 4 kW, 6 kW
3/N/PE ~ 400 V
– –
– Protection level IP 24 (splash-proof) – –
– Test symbols VDE / GS – –
Equipment level
– Thermal insulation
Permanently fixed/removable5) – Steel inner cylinder, enamel-
•/– •/– •/– –/• –/• –/• –/• –/• –/•
coated, with prot. anode • • • – – – – – –
– Temperature range
– Temperature limit
°C 35 to 82 – – – – – –
can be adjusted to °C 45 to 60 – – – – – –
– Contents HE DHW l – – – 41 53 65 41 53 65
– Area Solar internal indirect coil m2 – – – – – – 2.4 3.0 3.6
– Colour Pearl white Thermal insulation white Thermal insulation white
Weight and dimensions
– Height6) mm 1,570 1,585 1,755 1,840 2,250 2,190 1,840 2,250 2,190
– Height when tilted mm – – – 1,880 2,285 2,225 1,880 2,285 2,225
– Width mm ø 550 ø 650 ø 700 ø 790 ø 790 ø 1,000 ø 790 ø 790 ø 1,000
– Depth mm 690 790 840 910 910 1120 910 910 1,120
– Wet weight7) kg 255 368 485 950 1,175 1,736 995 1,220 1,791
4) Regulations vary according to local power supply company; to be connected only
by a qualified electrician.
5) Thermal insulation WD SBS as accessory, thickness 110 mm.
6) With water connector.
7) Before installing ensure the floor has sufficient load-bearing capacity.
58 | 59