Q-4â¢ Installation Manual - Viking Access

More documents

Recommendations

Info

LIMIT SWITCH SET-UP Note: Open and close the gate without interruption every time you change the adjustment. OPEN LEFT OPEN RIGHT R Gnd +28v Gnd UL Upper Cam sets Open Position Lower Cam sets Close Position Gnd Reopen Gnd Safety Connector Center Gnd Exit Gnd Strike Gnd Fire Open Commands Upper Cam sets Close Position Lower Cam sets Open Position Loop Connector Open Commands Guard Station Master/Slave Gnd Open Stop Close GND Guard Station Open Stop Close Master/Slave GND UL Siren UL Siren Siren Off 1 Center Loop Safety Loop UL Sens Radio Rec. Radio Rec. Radio Rec. STEP 1 Set the Fine Tune Limit Pot to Hold zero Open on the Control Board. UL Sensor UL Sensor Trim Pot Location Safety Loop Safety Loop Center Loop Center Loop off 1sec 30sec 30 Hold Open Timer MAX 60sec 60 Timer min. min. MAX Obstruction Sensor Sensor Hold Open Timer Obstruction Sensor Obstruction Open Close Stop Open Limit 0 3 0 Open 1.5 1.5 3 Overlap Delay Overlap Delay Stop Overlap Delay Stop Close Close Limit This ‘Trim Pot’ can be used to FINE ADJUST the closing position of the gate with a high degree of accuracy (up to 1/16”). The number on the Trim Pot dial sets the number of inches the gate travels after initial set-up. Brake Brake Brake OPEN LEFT STEP 2 Open the gate to the desired open position. Loosen and rotate the ‘Open’ Cam until the Limit Switch “clicks”. Tighten the cam. STEP 3 Close the gate to within 6” of desired closed position. Loosen and rotate the cam until the Limit Switch “clicks”. Tighten the cam. Upper Limit Switch Upper Cam Set Upper Cam in the Direction Shown Lower Limit Switch Lower Cam Set Lower Cam in the Direction Shown 16 Fail Safe/Secure Fail Safe/Secure TECHNICAL SUPPORT 1 800 908 0884 15
LIMIT SWITCH SET-UP STEP 4 Press both limit switches at the same time to initiate the set-up (the open and close LEDs will blink on the Control Board). Click! Click! Activate Both Limit Switches At the Same Time STEP 5 Open and close the gate from limit to limit without interruption for two complete cycles. 2X STEP 6 Fully Open and Close the Gate 2 Times Use the Fine Tune Limit Pot to perform minor adjustments to the closed position. 6" Initial Setting 2-1/2" First Adjustment 1/2" Fully Open and Close the Gate After Every Adjustment Second Adjustment TECHNICAL SUPPORT 1 800 908 0884 17
Page 1 and 2: VIKING installation instructions an
Page 3 and 4: Q-4 Vehicular Gate Operator • Rev
Page 5 and 6: TABLE OF CONTENTS Parts Diagram/Par
Page 7 and 8: IMPORTANT SAFETY INFORMATION WARNIN
Page 9 and 10: IMPORTANT SAFETY INFORMATION CAUTIO
Page 11 and 12: IMPORTANT SAFETY INFORMATION WARNIN
Page 13 and 14: OPEN STOP CLOSE IMPORTANT INSTALLAT
Page 15 and 16: PLAN OF INSTALLATION - CONCRETE PAD
Page 17 and 18: GATE OPERATOR INSTALLATION Step 3 C
Page 19: ELECTRICAL INSTALLATION Low Battery
Page 23 and 24: ELECTRICAL INSTALLATION - MASTER/SL
Page 25 and 26: VEHICULAR LOOP DETECTOR INSTALLATIO
Page 27 and 28: ACCESSORY CONNECTIONS 1 2 Photo Bea
Page 29 and 30: ACCESSORY CONNECTIONS Note: All con
Page 31 and 32: Mag. Lock Mag. Lock Mag. Lock SPECI
Page 33 and 34: Overlap Delay Overlap Delay p 3 1.5
Page 35 and 36: TROUBLESHOOTING Gate does not run -
Page 37 and 38: TROUBLESHOOTING Gate opens. Closes
Page 39 and 40: our continuous commitment to excell

Q-4â¢ Installation Manual - Viking Access

Create successful ePaper yourself

Delete template?

Save as template?

Q-4â¢ Installation Manual - Viking Access