INSTALLATION AND OPERATION MANUAL - Wood Pellet Stoves

More documents

Recommendations

Info

INSTALLATION INSTALLATION CHECK LIST It is strongly recommended that you have an authorized Lennox Hearth Products dealer install your stove. If you install your stove yourself, you should review your installation plan with an authorized Lennox Hearth Products dealer. Improper installation may void your warranty. Check list: Check off each item as you proceed with the installation process. � Read the ENTIRE stove installation section first � Read the Insert or Freestanding section (whichever applies). � Determine the appropriate measurements and locations for your installation. � Follow the general installation directions under Stove Installation and the installation section appropriate to your stove. � Be sure to pre-fit all items before you install, fasten, or set up the stove permanently. PAGE 10 www.PelletKing.com Prior to lighting your stove: � Review the Important Warnings section (page 2). � Review Fuel Specifications (page 25). � Review and follow instructions in the Care and Operation Section (pages 21 to 25). � Plug power cord connector into corresponding connector on the back of appliance (see illustrations on page 12 showing connector locations). Note: Advantage II-T C INS – Route power cord behind side surround panel. After you have begun operation of your stove: � Review the routine cleaning / maintenance information. � Enjoy the warmth from your new Lennox Hearth Products pellet stove! Advantage II-T C Insert It is important to level the appliance. In some installations such as a recessed firebox floor (if the existing fireplace floor is lower than the hearth), install the 2 leveling bolts (3/8-16 x 3 1/2” long) into the 2 threaded holes at the rear base of the Advantage II-T C INS. Adjust bolts until appliance is level.
INSTALLATION INSTALLING SURROUND ASSEMBLY - Advantage II-T C INS (to be done after venting system is installed) The surround kit (purchased separately) comes with a set of metal panels that enclose the fireplace opening when fitted together. Put the surround assembly together according to the following instructions (ref. see illustration below). 1. Remove panels from package. 2. Verify that you have all three panels and a package with “pop” rivets and #8 self-tapping screws. If you do not have a “pop” rivet tool, you should arrange to buy or borrow one for this installation. 3. Set the stove on the hearth so that the rear of the stove is accessible to complete all pipe connections. 4. Verify that the hopper cover is all the way to the front and open as high as your fireplace opening will allow. Secure the hopper cover with at least two #8 screws on all three sides. Tip: Spreading the side panels slightly may be necessary to complete this step. 5. Place four rivets and your “pop” rivet tool beside the stove and line up the right side panel (with control door) with the holes in the side of the stove. (When the side panel is properly installed, the hinge flange will be to the rear of the stove.) Attach the panel to the stove with four “pop” rivets. 6. Secure the left side surround panel to the stove using the procedure described in step #5. 7. Before proceeding further, check pipe connections to ensure that all joints are sealed with high-temperature RTV silicone and properly secured. Refer to detailed venting instructions on pages 16, 19 and 20. 8. The stove may now be pushed into the fireplace cavity to within 1 1/2” of the face of the fireplace. 9. Set the top surround panel in place over the two side panels. Carefully slide the panel downward into the “U” clips Optional Trim Top Surround Panel Left Hinged Surround Panel PAGE 11 attached to the back of the Advantage II-T C INS. Tip: Be careful to align the notched cutouts in the top surround panel with the stove side panels. Adjust side to side if necessary to align with the surround side panels. 10. Unwrap the control board carefully without touching any electrical components. Holding the sides of the control board, lower the bottom edge into the slot in the bottom of the control door opening Install the control board onto the right side panel (with door) using the #8 hex head screw provided. 11. Connect the wiring harness from the Advantage II-T C INS into corresponding connector on control board. 12. Check the Advantage II-T C INS placement in the fireplace. To reposition, open the door and make any needed adjustment by pulling forward and then pushing sideways. Once the unit has been centered to your satisfaction, close the door and push the Advantage II-T C INS back into place so the surround is flush with the face of the hearth. Tip: Before completing this step, verify that the control board will not hit the edge of the fireplace opening. If using the optional gold surround trim, remove the trim from its packaging and place the piece with the two mitered ends along the top panel. Place the two remaining side pieces on the surround so that the mitered ends align. Cut the non-mitered ends of the shroud trim with scissors, if necessary. In factory built and masonry fireplaces, a means must be provided to prevent room air passage to the chimney cavity of the fireplace. This may be accomplished by sealing the damper area around the chimney liner or pipe. Right Hinged Surround Panel www.PelletKing.com Optional Trim
Page 1 and 2: FREESTANDING AND INSERT PELLET FIRE
Page 3 and 4: TABLE OF CONTENTS Important Warning
Page 5 and 6: PLANNING YOUR INSTALLATION FLOOR PR
Page 7 and 8: PLANNING YOUR INSTALLATION MASONRY
Page 9: INSTALLATION REMOVING APPLIANCE FRO
Page 13 and 14: INSTALLATION VENTING REQUIREMENTS I
Page 15 and 16: INSTALLATION DETERMINING SIZE OF PI
Page 17 and 18: INSTALLATION Standard Horizontal In
Page 19 and 20: INSTALLATION - ADVANTAGE II-T C INS
Page 21 and 22: CARE AND OPERATION CONTROL BOARD OP
Page 23 and 24: CARE AND OPERATION Continued from l
Page 25 and 26: CARE AND OPERATION FUEL Clinkering
Page 27 and 28: ROUTINE MAINTENANCE ASH TRAP AND BA
Page 29 and 30: ROUTINE MAINTENANCE WINDOW WASH Per
Page 31 and 32: SPECIFICATIONS - Advantage II-T C F
Page 33 and 34: COMPONENT DEFINITIONS AIR WASH To i
Page 35 and 36: TROUBLESHOOTING Qualified Technicia
Page 37 and 38: TROUBLESHOOTING Qualified Technicia
Page 39 and 40: REPLACEMENT PARTS LIST Freestanding
Page 41 and 42: REPLACEMENT PART DIAGRAMS Pressure
Page 43 and 44: ADVANTAGE II-T C PELLET STOVE SAFET
Page 45 and 46: SIMPLE OPERATING INSTRUCTIONS LABEL
Page 47 and 48: OWNERSHIP RECORDS Dealer’s Name:

INSTALLATION AND OPERATION MANUAL - Wood Pellet Stoves

Create successful ePaper yourself

Delete template?

Save as template?