XC Repair Manual - Splendide

More documents

Recommendations

Info

Pump Motor A separate pump/pump motor is used to drain the drum (Fig. 3-1). The pump motor is 120 VAC and is attached directly to the pump. The pump has a filter located at the bottom-front that allows for the removal of large objects like keys and coins that may have passed from the basket. (Fig. 3-2) Drain Pump Large Object Filter Dryer Heating Element The Dryer Heating Element is located in the heater duct assembly on the top-right of the drum. The Module Board provides power to the element in the dry cycle. During the dry cycle: • Vented model (WD2100<strong>XC</strong>) take air from the surrounding room, heat it, tumble it through the clothes, and then exhaust it to the outside through a vent. • Ventless model (WDC7100<strong>XC</strong>) require 2.5 gallons of cold water per hour during the dry cycle. (See below.) Dryer Heating Element How Does Ventless Drying Work 1. As damp laundry tumbles, the inner drum is heated. Heat draws the moisture out of the laundry in the form of STEAM. 2. Cold water cools the OUTER TUB. The cold surface attracts the warm, saturated air. STEAM passes through the holes in the INNER DRUM to reach the OUTER TUB. 3. When the STEAM hits the cooled surface of the OUTER TUB, it’s condensed back into water. The water is then pumped out the drain. Process repeats until clothes are dry. NOTE: Do not attempt to dry less than 2.2 lbs of laundry during the Cotton Heavy Duty Dry cycle. 16 Theory of Operation
Door Lock/Switch Assembly The Door Lock/Switch Assembly is located on the right side of the door opening. The assembly contains a solinoid operated latching mechanism that will electrically lock the door during a wash or dry cycle. Door Lock/Switch Assembly Suspension System The drum assembly is held in position with two shock absorbers attached to the bottom sides of the tub assembly. In addition, the drum is suspended from the top frame of the washer with three springs attached to the sides of the case. Stability for this suspension system is provided by two concrete counter weights. One is located at the top and one at the bottom-front of the outer drum. Springs Top Counter Weight Bottom/Front Counter Weight Shock Absorbers Theory of Operation 17
Page 1 and 2: TRAINING GUIDE Splendide® TECHNICA
Page 3: Introduction Westland Sales assumes
Page 6 and 7: 5. Component Testing Procedures 39
Page 8 and 9: Warranty Guide* Refer to this page
Page 10 and 11: IMPORTANT General Safety Informatio
Page 12 and 13: Washer-Dryer Dimensions Und
Page 14 and 15: Electrical Requirements GROUNDING I
Page 16 and 17: Connecting the drain hose It is pos
Page 18 and 19: Completing the installation • •
Page 20 and 21: Pressure Switch The pressure switch
Page 24 and 25: Customer Interface / Cycle Selectio
Page 26 and 27: Resetting the Controls Clearing the
Page 28 and 29: Description of Preset Dry Cycles Co
Page 30 and 31: Automatic Routines The following ar
Page 32 and 33: 26 NOTES:
Page 34 and 35: Required Tools To access components
Page 36 and 37: Door / Door Switch / Porthole Diaph
Page 38 and 39: IMPORTANT! It’s very important to
Page 40 and 41: Removing the Heater Coil Remove the
Page 42 and 43: Before you disconnect the hoses, no
Page 44 and 45: Shock Absorbers The Shock Absorbers
Page 46 and 47: ! WARNING ELECTRICAL SHOCK HAZARD D
Page 48 and 49: 2. Power “in” from the Surge Pr
Page 50 and 51: 4. Heating Element Test Heating Ele
Page 52 and 53: 6. Fan Motor Test / Water Valve for
Page 54 and 55: 8. Control Panel Board Test Control
Page 56 and 57: Diagnosis & Troubleshooting Introdu
Page 58 and 59: DISPLAY Fault Code / Testing Proced
Page 60 and 61: DISPLAY Problem / Testing Procedure
Page 62 and 63: Tech Tips Manually Unlocking the Do
Page 64 and 65: DISPLAY Verifying Normal Operation
Page 66 and 67: WD2100XC / WD2100XCP / WD7100XCP MO
Page 68: Splendide ® © Copyright 2007, Wes

XC Repair Manual - Splendide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?