XC Repair Manual - Splendide

More documents

Recommendations

Info

! WARNING ELECTRICAL SHOCK HAZARD Disconnect power before servicing. Replace all panels before operating. Failure to do so can result in death or electrical shock. Introduction Before testing the components, ALWAYS: • Make sure that the power cord is firmly plugged into a live circuit with the proper voltage. • Check for a blown household fuse or circuit breaker that has tripped. • Make sure that the dryer vent is properly installed and clear of lint obstructions. (WD2100<strong>XC</strong> Only.) When testing, follow these instructions: • Resistance tests MUST be made with the power cord unplugged from the outlet, and the wire connector removed from the Module Board. • All tests should be made with a VOM (volt ohmmeter) or DVM (digital volt ohmmeter) having a sensitivity of 20,000 ohms-per-volt DC or greater. • BEFORE replacing any component, ALWAYS check for wire connectors that are not pressed tightly into their terminals. Tests MUST be made with ALL connectors attached. Look for broken or loose wires, failed terminals, or wires that are not pressed into their connectors far enough. Your Test Results If the readings you obtain with the following tests match the specified range, the tested component is operating correctly. If the readings you obtain are not in the specified range, call <strong>Splendide</strong> Service at 1-800-356-0766 (503-655-2563) ext. 5 for further assistance. Have the Model and Serial Number of your machine ready when you call. 40 Component Testing Procedures
1. Door Switch Testing Door Switch Test Points are located on the connector on the Module Board and on the Door Switch (See “Connector Locations on the Module Board”) 321 J4 on Module Board 3 4 5 Door Switch Fault Codes: F17 Test Points Reading Door Switch to J4 3 to 3 0 ohms Door Switch to J4 4 to 2 0 ohms Door Switch to J4 5 to 1 0 ohms Component Testing Procedures 41
Page 1 and 2: TRAINING GUIDE Splendide® TECHNICA
Page 3: Introduction Westland Sales assumes
Page 6 and 7: 5. Component Testing Procedures 39
Page 8 and 9: Warranty Guide* Refer to this page
Page 10 and 11: IMPORTANT General Safety Informatio
Page 12 and 13: Washer-Dryer Dimensions Und
Page 14 and 15: Electrical Requirements GROUNDING I
Page 16 and 17: Connecting the drain hose It is pos
Page 18 and 19: Completing the installation • •
Page 20 and 21: Pressure Switch The pressure switch
Page 22 and 23: Pump Motor A separate pump/pump mot
Page 24 and 25: Customer Interface / Cycle Selectio
Page 26 and 27: Resetting the Controls Clearing the
Page 28 and 29: Description of Preset Dry Cycles Co
Page 30 and 31: Automatic Routines The following ar
Page 32 and 33: 26 NOTES:
Page 34 and 35: Required Tools To access components
Page 36 and 37: Door / Door Switch / Porthole Diaph
Page 38 and 39: IMPORTANT! It’s very important to
Page 40 and 41: Removing the Heater Coil Remove the
Page 42 and 43: Before you disconnect the hoses, no
Page 44 and 45: Shock Absorbers The Shock Absorbers
Page 48 and 49: 2. Power “in” from the Surge Pr
Page 50 and 51: 4. Heating Element Test Heating Ele
Page 52 and 53: 6. Fan Motor Test / Water Valve for
Page 54 and 55: 8. Control Panel Board Test Control
Page 56 and 57: Diagnosis & Troubleshooting Introdu
Page 58 and 59: DISPLAY Fault Code / Testing Proced
Page 60 and 61: DISPLAY Problem / Testing Procedure
Page 62 and 63: Tech Tips Manually Unlocking the Do
Page 64 and 65: DISPLAY Verifying Normal Operation
Page 66 and 67: WD2100XC / WD2100XCP / WD7100XCP MO
Page 68: Splendide ® © Copyright 2007, Wes

XC Repair Manual - Splendide

Create successful ePaper yourself

Delete template?

Save as template?